User manual ICOM IC-FR6100

[. . . ] INSTRUCTION MANUAL VHF FM REPEATER iFR5100 UHF FM REPEATER iFR6100 IMPORTANT R E A D T H I S I N S T RU C T I O N M A N UA L CAREFULLY before attempting to operate the repeater. EXPLICIT DEFINITIONS WORD RWARNING CAUTION NOTE DEFINITION Personal injury, fire hazard or electric shock may occur. No risk of personal injury, fire or electric shock. SAVE THIS INSTRUCTION MANUAL­ This manual contains important safety and operating instructions for the IC-FR5100/IC-FR6100 vhf/uhf fm repeaters. PRECAUTIONS R WARNING HIGH VOLTAGE!NEVER attach an antenna or internal antenna connector during transmission. This may result in an electrical shock or burn. [. . . ] Input terminal for serial communication data. Output terminal for request-to-send data. No connection Serial/digital signal ground Modulator input from an external terminal unit. Output terminal for AF signals from the AF detector circuit. Output level is fixed, regardless of [AF] control. The desired function can be assigned. * (Default: Null) 13. 2 V DC output Customize A/D input (Not used) No connection Ground The desired function can be assigned. * (Default: Null) The desired function can be assigned. * (Default: P0 Monitor Output) The desired function can be assigned. * (Default: Busy Output) The desired function can be assigned. * (Default: Null) The desired function can be assigned. * (Default: EPTT Input) Input terminal for data. The desired function can be assigned. * (Default: Analog Audible Output) The AF detector Output. The desired function can be assigned. * (Default: Mic Mute Output) The desired function can be assigned. * (Default: Null) The desired function can be assigned. * (Default: Mic Hanger Output) Specification -- -- -- -- -- -- -- Input level: 300 mV rms Output level: 300 mV rms -- Output current: Less than 1 A -- -- -- +5 V pull up, Active=L +5 V pull up, Active=L +5 V pull up, Active=L +5 V pull up, Active=L +5 V pull up, Active=L -- +5 V pull up, Active=L -- +5 V pull up, Active=L +5 V pull up, Active=L +5 V pull up, Active=L * The desired function can be assigned using the optional CS-FR5000 cloning software. 3 INSTALLATION AND CONNECTIONS n Unpacking After unpacking, immediately report any damage to the delivering carrier or dealer. For a description and a diagram of accessory equipment included with the repeater, see `SUPPLIED ACCESSORIES' on p. ii of this manual. 2 n Antenna connection For radio communications, the antenna is a critical component, along with output power and sensitivity. Select antenna(s), such as a well-matched 50 antenna, and feedline. NEVER remove the fuse-holder from the DC power receptacle. AC outlet DC power supply 13. 2 V; at least 20 A Red Black + _ R When you disconnect the DC power cable, take care no crack of your fingernail. w q Push Supplied DC power cable AC cable Red Black 5 INSTALLATION AND CONNECTIONS 2 n Power supply connection Make sure the repeater's power is turned OFF when connecting a DC power cable. CAUTION: Voltages greater than 16 V DC will damage the repeater. Check the source voltage before connecting the power cable. n Mounting the repeater D Using the supplied handle The supplied handles are available for mounting the repeater into a 19 inch rack. The handles can be installed to the repeater's front panel. q Attach the supplied handles to both sides of the repeater's front panel with the spacers, then tighten the screws as below. 1 P0 P1 P2 P3 P4 Screw Handle Spacer 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 6 w The completed installation should look like as below. P0 P1 P2 P3 P4 3 OPERATION n Receiving and transmitting D Repeater operation Ask your dealer for details of the repeater's programming. hen the power is turned ON, the [PWR] indicator W lights green. 1) he [TX] and [BUSY] indicators light simultaneT ously while transmitting/receiving a signal. · The [TX] indicator lights red. · The [BUSY] indicator lights green. D Base station operation Receiving q Push [POWER] to turn the power ON. Rotate [SELECT]*1 fully counterclockwise in advance. [. . . ] Referring to the table above for VHF/UHF vertical antennas, this gives a front clearance distance of approx. The antenna installation needs to ensure that the lowest part of the antenna is at least 3 m above any point where the general public may gain access and that they cannot pass within 1. 5 m in front of the antenna. If there is no general public access to the roof in question then the antenna could be mounted on a short stub mast. If there is such access to the roof then the antenna could be mounted on top of a short mast of 3. 2 m high. [. . . ]