User manual ICOM IC-M11

[. . . ] If the antenna cannot be installed at 6 meters or graterI, we recommend touse the one watt setting to minimize RF exposure. In all cases any possible risk depends on the transmitter being activated for long periods. (actual recommendation limits are specified as an average of 6 minutes) Normally the transmitter is not active for long periods of time. Some radio licenses will require that a timer circuit automatically cuts the transmitter after 1­2 minutes etc. i SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-M11. IN CASE OF EMERGENCY If your vessel requires assistance, contact other vessels and the Coast Guard by sending a distress call on Channel 16. [. . . ] [Example]: Starting a priority scan. t To stop the scan, push [Y] or [Z]. Push [Y] or [Z] for 1 sec. I I I Scan starts. When a signal is received 10 6 DSC OPERATION e Check the 9-digit MMSI (DSC self ID) code. r Push [DSC] to exit the condition. I s MMSI code programming The 9-digit MMSI (DSC self ID) code can be programmed at power ON. This function is not available when the MMSI code has been programmed by the dealer. This code programming can be performed only 2 times. w While pushing [DSC], turn power ON to enter MMSI code programming condition. e After the display appears, release [DSC]. r Select the desired number by pushing [Y]/[Z] . t Push [H/L] to advance the cursor. · Push [CH/WX] to move the cursor backward. s Position indication When an optional GPS receiver (NMEA0183 ver. 2. 0) is connected, the transceiver can display the current position and time. A GPS receiver appropriate for the IC-M11 is not supplied from Icom. 2. 0 is required for position indication. 14 6 DSC OPERATION Transmitting position reply call Transmit a position reply call when a position request call is received. q "DSC" appears and a"RCV Pos request" scrolls in the display. I Transmitting position request call Transmit a position request call when you want to know your friend's current position, etc. q Select a desired channel other than Channel 70. w Push [DSC] to select the DSC menu e Push [Y]/[Z] to select "POS REQUEST". I w Push [DSC] to reply to the position request call; push [H/L] to ignore the position request call. r Push [Y]/[Z] to select the desired preprogrammed individual address. · The ID code for position request can be set in advance. 16) · "OK" appears. I t Push [DSC] to enter pre-programmed individual address. y Push [DSC] to transmit the position request call. · Channel 70 is selected and the position request call is transmitted. I u The position request call has been transmitted. · "WAITING ACK" scrolls. I i Push [PTT] or rotate the channel selector to exit the condition. 15 DSC OPERATION 6 s DSC individual ID A total of 30 DSC address ID's can be programmed and named with up to 10 characters. Deleting address ID q Push [DSC] to select the DSC menu. w Push [Y]/[Z] to select "ADDRESS" and push [DSC]. e Push [Y]/[Z] to select `DEL, ' then push [DSC]. · When no address ID is programmed, the transceiver exits the condition automatically. I Programming address ID q Push [DSC] to select the DSC menu. w Push [Y]/[Z] to select "ADDRESS" and push [DSC]. I e Push [Y]/[Z] to select "ADD" and push [DSC]. I r Select the desired ID name pushing [Y]/[Z], then push [DSC]. t Push [DSC] to delete the address ID; push an other switch to exit the condition. I r Set the distress ID and ID name, then push [DSC]. · Rotate the channel selector to select the character. [. . . ] · Only [PWR] and [PTT] are functional. The monitor function releases the noise squelch mute of the microphone only. (An independent noise squelch system is employed. ) Push [SQL·MONI] for 1 sec. to activate the monitor function. ·" " flashes and audio is emitted. · Any key, except [Y]/[Z], cancels the monitor function. 38 13 HM-127 REMOTE-CONTROL MICROPHONE s Call channel programming. q Push [CH/WX·U/I/C] several times while pushing [H/L] to select the desired channel group (USA, INT, CAN) to be programmed. [. . . ]