User manual ICOM IC-M58

[. . . ] This manual contains important safety and operating instructions for the IC-M58. EXPLICIT DEFINITIONS WORD R WARNING CAUTION NOTE DEFINITION Personal injury, fire hazard or electric shock may occur. No risk or personal injury, fire or electric shock. D FEATURES Standard 4×8 remote controller Built-in DSC meets ITU Class E requirement 12 and 24 V DC versions are available PC connection capability for remote control PRECAUTIONS R WARNING HIGH VOLTAGE!NEVER attach an antenna or internal antenna connector during transmission. This may result in an electrical shock or burn. [. . . ] They are never renewed during the voyage when the position is set manually. When a position and the UTC time data (NMEA0183 ver. 3. 01 format) is applied to [GPS], the following steps are not necessary. y Push [MODE SET] to enter the DSC menu. · DSC menu is displayed as below. q While pushing and holding [MODE [POWER] to enter initial set mode. · Turn the power OFF in advance. SET] push u Rotate [CH] to select "Position, " then push [ENT]. [MODE SET] [POWER] ******* DSC MENU ******* -------- Select -------ÇP o s i t i o n Individual Group Position REQ Distress Distress RLY SEL OK w Rotate [GRP] to select the "GPS DISPLAY" then rotate [CH] to select the desired position indication type from simple and detail. *** SET MODE *** i Enter your position and the UTC time via the keypad, then push [ENT]. · Push [3 SCAN] for the `East, ' [9] for the `West, ' [6 RF-G] for the `North' and [7] for the `South' setting. · Rotate [CH] to move the cursor. 6 ÇÇ S I M P L E DETAIL ITEM SEL e Rotate [GRP] to select the "OFFSET TIME" then rotate [CH] to set the time difference between local and the UTC times within ­12 to +12 hours in 10 minute steps. *** SET MODE *** ******* Position ******* --- Position & time ---34 34. 343N Latitude Longitude 135 34. 343E 12:34 UTC Null OK o Push [ENT] to program the position and time. · Return to the "DSC MENU" indication as in step u. !0 Push [MODE SET] to exit the DSC menu. ITEM SEL · Rotate [CH] to select "Exit" then push [ENT] also exits set mode. · "MNL" appears instead of "GPS. " r Turn the power OFF once, then ON again to exit quick set mode. · Simple position indication · Detail position indication MMSI 123456789 12. 345. 0 F1B GPS Lat 34 34'N SP Lon135 34'E 12:34 Exit MMSI 123456789 12. 345. 0 F1B GPS 34 34. 000N SP 135 34. 000E 12:34 Exit 15 7 CALL PROCEDURE I Distress call A distress call should be transmitted if in the opinion of the Master, the ship or person is in distress and requires immediate assistance. A distress call should include the ship's position and time. They are included automatically when their data in NMEA0183 ver. 3. 01 format is applied to [GPS] connector. When no data is applied, input them, if possible. A distress call some times called as a "MAYDAY call. " NEVER USE THE DISTRESS CALL WHEN YOUR SHIP OR A PERSON IS NOT IN AN EMERGENCY. Push [CANCEL] only when you want to cancel repeated transmission. D After receiving an acknowledgement call The following should commence your voice transmission after receiving a distress acknowledgement from a coast station (or another ship). · "MAYDAY" · "This is . . . . . (your ship name). " · The 9-digit identity AND the call sign (or other identification of the ship). · The ship's position if the DSC distress does not included it. · The nature of the distress and assistance required. · Any other information which might facilitate the rescue. 7 19 7 CALL PROCEDURE I Individual call When you use DSC for general selective calling, perform as follows. D Operation outline DSC menu ******* DSC MENU ******* -------- Select -------Position ÇI n d i v i d u a l Group Geographical Distress Distress RLY Semi/Auto Test RX memory TX memory Set up Self test ÇE x i t SEL OK Address ID selection ****** Individual ****** ------ Address ID -----ÇM a n u a l s e t 123456789 IC-M801-1 123456788 IC-M801-2 123456787 IC-M801-3 123456786 IC-M801-4 123456785 IC-M801-5 SEL OK Manual ID input ****** Individual ****** ------ Address ID -----________ OK Traffic frequency selection 1 ****** Individual ****** -- Traffic frequency --Manual set Traffic frequency selection 2 ****** Individual ****** -- Traffic frequency --TX:_2134. 0kHz RX:_2134. 0kHz OK Call frequency selection 1 ****** Individual ****** ---- Call frequency ---Manual set ÇT : 2 1 3 4 . 0 k H z I C - M 8 0 1 - 1 R: 2134. 0kHz T:12345. 0kHz IC-M801-2 R:12345. 0kHz SEL OK ÇT : 2 1 7 7 . 0 k H z S H I P R: 2177. 0kHz T: 2189. 5kHz INTER2-1 R: 2177. 0kHz SEL OK Call frequency selection 2 ****** Individual ****** ---- Call frequency ---TX:2177. 0kHz RX:_2177. 0kHz OK Confirmation screen ****** Individual ****** --------- Call --------To:IC-M801_1 Category:Routine Traffic:J3E TX 2134. 0kHz RX 2134. 0kHz 2177. 0kHz Call Freq:TX RX 2177. 0kHz Write-Menu Call Push [CALL] for 1 sec. to store the condition into the TX memory channel. 20 CALL PROCEDURE 7 D Individual call operation q Push [MODE SET] to select the DSC menu. w Rotate [CH] to select "Individual, " then push [ENT]. e Select (or enter) the 9-digit ID code, then push [ENT]. · Use [CH] to select the ID code when the desired ship's ID is pre-programmed. ****** Individual ****** ------ Address ID -----ÇM a n u a l s e t 123456789 IC-M801-1 123456788 IC-M801-2 123456787 IC-M801-3 123456786 IC-M801-4 123456785 IC-M801-5 SEL OK t Rotate [CH] to select the desired pre-programmed calling frequency, or "Manual set" then push [ENT]. When the pre-programmed call frequency is selected, go to step y. ****** Individual ****** ---- Call frequency ---Manual set ÇT : 2 1 7 7 . [. . . ] to program the user channel. · 3 beeps sound and "" disappears. RX J3E SIMP e Enter 4 to 6 digits of the desired frequency via the keypad. · Or rotate [GRP] and [CH] to change the frequency. · Pushing [Y]/[Z] on the microphone also tunes the frequency. CH ---GPS--Lat 45 59'N Lon134 44'E 0 1 2 3 4A 16:23 "Ç" indicator disappears when programming is completed. D Transmit frequency q Select the desired channel to be programmed. to program the user channel. · 3 beeps sound. RX TX J3E SIMP CH ---GPS--Lat 45 59'N Lon134 44'E 0 1 2 3 4A 16:23 "T X" indicator blinks. CH ---GPS--Lat 45 59'N Lon134 44'E 0 1 2 3 4A 16:23 e Enter the desired 5 or 6 digit frequency via the keypad. · [GRP] and [CH], as well as [Y]/[Z] on the microphone cannot be used. RX J3E SIMP "T X" indicator disappears. TX CH ---GPS--Lat 45 59'N Lon134 44'E 0 1 2 3 4A 16:23 62 SPECIFICATIONS · General · Frequency coverage Receive Transmit : (Unit: MHz) 14 · Transmitter 0. 5­29. 9999 1. 6­2. 9999 4. 0­4. 9999 6. 0­6. 9999 8. 0­8. 9999 12. 0­13. 9999 16. 0­17. 9999 18. 0­19. 9999 22. 0­22. 9999 25. 0­27. 5000 : 2, 187. 5 kHz, 4, 207. 5 kHz, 6, 312. 0 kHz, 8, 414. 5 kHz, 12, 577. 0 kHz, 16, 804. 5 kHz : J3E (USB/LSB*), H3E, * J2B (AFSK), F1B (FSK), A1A* (CW) F1B *Receive only · DSC channels · Output power 1. 6­3. 9999 MHz 4. 0­27. 5000 MHz · Spurious emission · Carrier suppression · Unwanted sideband suppression · Mic. connector : 85 W p-p 125 W p­p : 43 dB below peak output power : 40 dB below peak output power : 55 dB below peak output power (w/1 kHz AF input; at max power) : 8-pin connector (2. 4 k) · Receiver · Sensitivity Transceiver · Type of emission Transceiver DSC receiver · No. [. . . ]