User manual ICOM IC-P2A-E

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ICOM IC-P2A-E. We hope that this ICOM IC-P2A-E user guide will be useful to you.

Lastmanuals help download the user guide ICOM IC-P2A-E.


Mode d'emploi ICOM IC-P2A-E
Download

You may also download the following manuals related to this product:

   ICOM IC-P2A-E (3233 ko)

Manual abstract: user guide ICOM IC-P2A-E

Detailed instructions for use are in the User's Guide.

[. . . ] AVOID using or placing the linear amplifier or remote controller in areas with temperatures below ­10°C (+14°F) or above +40°C (+104°F). AVOID placing the linear amplifier or remote controller in excessively dusty environments or in direct sunlight. AVOID placing the linear amplifier against walls or putting anything on top of the linear amplifier. The linear amplifier will become hot when operating if continuously for long periods. [. . . ] If operation continues using this setup, damage (including the possibility of explosion) to the connected transceiver and/or IC-P2A-E/EURO will occur. Icom standard 8 and 7-pin accessory jacks (transceiver side) [ACC(1)] 2 4 5 1 83 6 7 [ACC(2)] 4 1 6 2 5 3 7 · Using 1 Icom exciter (transceiver) To an antenna Remote control cable (supplied) ACC-1 ACC cable (supplied) Be sure to connect the cable to the 7-pin ACC(2) jack. INPUT1 INPUT2 Coaxial cable (optional) EXCITER 1 1&2 ANT2 GND Coaxial cable (supplied) Connect [INPUT2] if necessary. ANT1 ACC(2) REMOTE ANT REMOTE GND IC-P2A-E/EURO AC outlet (IC-P2A-E : 100­120/220­240 V IC-P2A-EEURO : 230 V) Ground IC-756 7 INSTALLATION AND CONNECTIONS 2 · Using a 13-pin ACC socket (IC-706 series) Remote control cable (supplied) To an antenna ACC-1 OPC-599 (optional) ACC cable (supplied) ANT REMOTE INPUT1 Coaxial cable (supplied) GND EXCITER 1 1&2 ANT1 ACC (13 pins) REMOTE IC-706 series GND IC-P2A-E/EURO AC outlet (IC-P2A-E : 100­120/220­240 V IC-P2A-EEURO : 230 V) Ground · Using 2 Icom exciters (transceivers) The following connections also apply to transceivers having multiple antenna connectors for specified bands (e. g. IC-726, IC-729, etc. ) Remote control cable (supplied) OPC-599 (optional) ACC cable (supplied) ACC REMOTE To an antenna ACC-1 ANT REMOTE Coaxial cable (supplied) INPUT1 ANT1 ACC-2 REMOTE EXCITER 1 1&2 INPUT2 OPK-5 (optional) GND GND IC-706 series IC-756 ANT1 or 2 GND Ground IC-P2A-E/EURO AC outlet ACC(2) (IC-P2A-E : 100­120/220­240 V IC-P2A-EEURO : 230 V) Optional ACC cable (includedn in the OPK-5) Optional remote control cable (includedn in the OPK-5) Be sure to connect the cable to the 7-pin ACC(2) jack. REMOTE 8 2 INSTALLATION AND CONNECTIONS · Using a non-Icom exciter (transceiver) Set the [EXCITER] switch to [1] when 1 exciter is connected; set to [1&2] when 2 exciters are connected. To an antenna ALC1 ANT SEND1 INPUT1 SEND NOTE: The specifications for the SEND relay are 5 V DC 0. 1 A. If this level is exceeded, a large external relay must be used. RCA plug ALC SEND DC power Relay EXCITER 1 1&2 GND Coaxial cable (supplied) RF OUT DC OUT SEND ALC GND IC-P2A-E/EURO AC outlet (IC-P2A-E : 100­120/220­240 V IC-P2A-EEURO : 230 V) Ground Non-Icom exciter · Using 1 Icom and 1 non-Icom exciters (transceivers) To an antenna ACC-1 ACC cable (supplied) NOTE: The specifications for the SEND relay are 5 V DC 0. 1 A. If this level is exceeded, a large external relay must be used. Be sure to connect the cable to the 7-pin ACC(2) jack. Remote control cable (supplied) ACC(2) ANT REMOTE Coaxial cable (supplied) INPUT1 INPUT2 GND Connect ANT1 or ANT2 REMOTE IC-756 EXCITER 1 1&2 GND ANT RF OUT Non-Icom exciter IC-P2A-E/EURO AC outlet (IC-P2A-E : 100­120/220­240 V IC-P2A-EEURO : 230 V) SEND2 Ground Coaxial cable (optional) SEND SEND SEND DC OUT ALC GND Relay ALC2 RCA plug DC power ALC 9 INSTALLATION AND CONNECTIONS 2 · Using non-Icom exciters (transceivers) when the IC-P2A-E/EURO's power is OFF To use the antenna selector of the IC-P2A-E/EURO while the power is OFF, follow 1 of 2 methods. (1) Supply the antenna selector power to the ACC-1 socket Supply the 13. 8 V DC, 0. 5 A to pin 7 of the [ACC-1]/ [ACC-2] socket. - Use [ACC-1] when the exciter is connected to [INPUT1]. - Use [ACC-2] when the exciter is connected to [INPUT2]. to IC-P2A-E/EURO [INPUT1] 13. 8 V DC to IC-P2A-E/EURO [GND] 3 RF DC SEND ALC GND (2) Use the auxiliary power supply Set the jumper to `2' to use the auxiliary power supply as shown at right. - The antenna selector functions even when the ICPW1/EURO power is OFF [ACC-1] 6 1 524 In addition set the jumper on the IC-P2A-E/EURO controller to `2' to turn the controller's LEDs OFF as shown at right. When the jumper is set to `2, ' the CI-V control does not function even if an Icom exciter is connected. ·Jumper location of linear amplifier IC-P2A-E/EURO (DIN) Non-Icom exciter S3 J4 J3 2 1 · Jumper location of controller 12 These diagrams show the factory defaults. NOTE: When using the antenna selector of the IC-P2A-E/EURO while the power is OFF, as above, tuner intialization of the IC-P2A-E/EURO may not be performed correctly if the applied voltage is insufficient. Check that the applied voltage to pin 7 of [ACC-1]/[ACC-2] socket is 13. 8 V DC. 10 2 INSTALLATION AND CONNECTIONS I Separating the remote controller The control section of the linear amplifier can be separated from the main body, doubling as a remote controller. w Set the 1st exciter's RF output power for the minimum output. e Be sure that the [ALC adj1] and [ALC adj2] pots on the rear panel max. (default) [ALC adj2] [ALC adj1] y Push the transmit meter-2 switch one or more times to select the ALC level meter. - The [ALC] indicator lights. u Push [TUNER] to turn the antenna tuner ON. - The [TUNER] light lights. i While adjusting the 1st exciter's RF output power, transmit a 100 W output power of the selected band signal using CW or RTTY mode. o Adjust the [ALC adj1] pot to the ALC adjustment point as shown below. ALC adjustment point METER-2 !0 Check that the Po meter shows 1 kW output power. 100 0 Po ID TEMP 0 10 250 500 50 HOT 1K 60 1. 5K W A Output power 20 30 40 METER-1 r Push [POWER] to turn the linear amplifier power ON. t Push [UP] or [DOWN] to select an operating band except 50 MHz band. - Select a band which uses a well-matched 50 antenna. !1 Adjust the [ALC adj2] pot in the same manner when a 2nd exciter is connected. 12 3 OPERATION I Programming the CI-V address The IC-P2A-E/EURO uses CI-V frequency data for automatic selection of the operating band. Program the exciter's address to use this capability as follows: For non-Icom exciters, the IC-P2A-E/EURO cannot be controlled using the CI-V function, so this setting is not necessary. For transceivers which have multiple antenna connectors for specified bands (e. g. IC-726, IC-729, etc. ), set the same as for 2 Icom exciters. D When using 1 Icom exciter q While pushing [INPUT], push [POWER] to enter the CI-V address programming mode. - [INPUT z] blinks. HF/50MHz ALL BAND 1kW LINEAR AMPLIFIER POWER iPW1 z Po VD SWR ALC x INPUT TRANSMIT ID TEMP METER-1 TUNER METER-2 z x c v ANT AMP/ PROTECT DOWN AUTO 1. 8 3. 5 7 10 14 18 21 24 28 50 UP D Setting the Icom exciters When connecting 2 or more CI-V devices: DO NOT use the "AUTO" baud rate for CI-V devices. We recommend that all CI-V devices are set to 9600 bps. · When using the same baud rate, the exciters' frequencies are synchronized. · When using different baud rates (i. e. [. . . ] · The linear amplifier is located in an area with bad air circulation. · [ALC adj] is not adjusted properly. 18 5 SPECIFICATIONS I Transmitter · Output power MODE 200­240 V AC CW, RTTY SSB 1 kW 1 kW PEP 100­120 V AC 500 W 500 W PEP I General · Frequency coverage: 01. 800­01. 999 MHz 03. 500­13. 999 MHz 07. 000­17. 300 MHz 10. 100­10. 150 MHz 14. 000­14. 350 MHz 18. 068­18. 168 MHz 21. 000­21. 450 MHz 24. 890­24. 990 MHz*1 28. 000­29. 700 MHz*1 50. 000­54. 000 MHz *1 The U. S. A. version can only be used the antenna tuner on the 24­28 MHz bands. : INPUT AC VOLTAGE · Driving power : 100 W max. · Spurious emissions : ­60 dB (HF bands) ­70 dB (50 MHz band) · SEND connector · ALC connector : Phono (RCA) : Phono (RCA) · Antenna connector Input Output : PL-239 × 2 (50 ) PL-239 × 4 (50 ) I Antenna tuner · Matching impedance range: HF bands*2 16. 7 to 150 unbalanced (Less than VSWR 3:1) · Usable temperature : ­10°C to 40°C (14°F to 104°F) range · Power supply requirement: non-Europe versions 100­120 V AC or 200­240 V AC (±10 %) Europe version 230 V AC (±10 %) · Dimensions (W × H × D): Linear amplifier 350 × 265 × 375 mm 13 25/32 × 10 7/16 × 14 3/4 in Remote controller 205 × 71 × 68. 3 mm 8 1/16 × 2 25/32 × 2 11/16 in (Projections not included) 50 MHz band 20 to 125 unbalanced (Less than VSWR 2. 5:1) *2 The U. S. A. version can only be tuned within 1. 80­1. 95 MHz of the 1. 8 MHz band. · Minimum operating input power: 60 W · Tuning accuracy · Insertion loss : VSWR 1. 5:1 or less : Less than 1. 0 dB (after tuning) · Weight · CI-V connector : Approx. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE ICOM IC-P2A-E

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual ICOM IC-P2A-E will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag