User manual ICOM IC-P7A

[. . . ] INSTRUCTION MANUAL VHF/UHF DUAL BAND FM TRANSCEIVER iP7A This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIO TELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. FOREWORD Thank you for purchasing this Icom product. The IC-P7A VHF/UHF DUALBAND FM TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. [. . . ] to set the channel into the bank. · Return to the previous indication. DTCS ATT S. MW SET VOL PRIO P SKIP MR 9 5 LOW 1 25 MEMORY/CALL CHANNELS 6 Memory bank selection qPush [V/M] (SKIP·S. MW) to select memory mode, if desired. wWhile pushing and holding [BAND] (TS·LOCK), rotate [DIAL] to select the desired bank (A to H, J, L, N, O to R, T, U and Y). · The bank can also be selected by pushing [BAND] (TS·LOCK) several times. · The only programmed banks are displayed. WFMAM -DUP T SQL DTCS ATT WFMAM -DUP T SQL DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 Rotate [DIAL] while pushing [BAND] WFMAM -DUP T SQL Only programmed banks appear WFMAM -DUP T SQL DTCS ATT DTCS ATT 6 [DIAL] VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 Auto write channels eRotate [DIAL] to select the bank channel. · Only programmed channels are displayed. WFMAM -DUP T SQL SCAN DTCS ATT S. MW VOL PRIO P SKIP MR 9 5 LOW 1 SET Bank initial Bank channel number rTo return to regular memory operation, rotate [DIAL] while pushing and holding [BAND] (TS·LOCK), or push [BAND] (TS·LOCK) several times. Push Push and hold Dual operation 26 6 MEMORY/CALL CHANNELS Programming memory/bank name Each memory channel can be programmed with an alphanumeric channel name for easy recognition and that can be indicated independently by channel. q Push [V/M] (SKIP·S. MW) to select memory mode. w Rotate [DIAL] to select the desired memory channel. ePush and hold [V/M] (SKIP·S. MW) for 1 sec. to enter select memory write mode. · 1 short and 1 long beep sound. ·" " indicator and memory channel number blink. WFMAM -DUP T SQL tWhile pushing and holding [FUNC], rotate [DIAL] to select the desired character. · The selected character blinks. y Rotate [DIAL] to move the cursor to left or right. Memory name WFMAM -DUP T SQL Bank name WFMAM -DUP T SQL DTCS ATT DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 uRepeat steps t and y until the desired 6-character channel names are displayed. iPush [CALL] (MODE·SCAN) several times, or rotate [DIAL] while pushing and holding [CALL] (MODE·SCAN) to select "S. MW. " WFMAM -DUP T SQL DTCS ATT rWhile pushing and holding [CALL] (MODE·SCAN), rotate [DIAL] to select "M NAME" or "B NAME" when programming the memory name or the bank name, respectively. · Name type can also be selected by pushing [CALL] (MODE·SCAN) several times. · After releasing [CALL] (MODE·SCAN), an under bar blinks for the first digit instead of the frequency indication, and only " " indicator blinks. Memory name selection WFMAM -DUP T SQL VOL PRIO P SKIP MR 9 5 LOW 1 oPush and hold [V/M] (SKIP·S. MW) for 1 sec. to program the name and exit the channel name programming. · 3 beeps sound. Bank name selection WFMAM -DUP T SQL DTCS ATT DTCS ATT · Available characters A to Z, 0 to 9, (, ), , +, ­, . , /, :, = and space. VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 27 MEMORY/CALL CHANNELS 6 Selecting display type During memory mode operation, the programmed memory name, bank name or the channel number can be displayed instead of the frequency at your preference. WFMAM -DUP T SQL D Selecting bank channel indication During bank channel operation, the bank channel number can also be displayed instead of the memory channel number indication. Memory channel No. indication WFMAM -DUP T SQL DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 WFMAM -DUP T SQL DTCS ATT DTCS ATT 6 Push [BAND] momentarily while pushing [FUNC] WFMAM -DUP T SQL VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 DTCS ATT Push [BAND] SCAN VOL PRIO P SKIP MR 9 5 LOW 1 S. MW WFMAM -DUP T SQL DTCS ATT WFMAM -DUP T SQL DTCS ATT SET WFMAM -DUP T SQL DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 Auto write channel No. VOL PRIO P SKIP MR 9 5 LOW 1 Bank channel No. indication When no memory or bank name is programmed with the selected memory channel, frequency is displayed on the function display. WFMAM -DUP T SQL DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 After selecting channel number indication as described at left, push [BAND] (TS·LOCK) to select the desired bank. Or while pushing and holding [BAND] (TS·LOCK), rotate [DIAL] to select the desired bank. q Push [V/M] (SKIP·S. MW) to select memory mode. · [BAND] (TS·LOCK) to select the desired bank. wWhile pushing and holding [FUNC], push [BAND] (TS·LOCK) momentarily to select display type from frequency, bank name, memory name and channel number display. Push Push and hold Dual operation 28 6 MEMORY/CALL CHANNELS Copying memory contents This function transfers a memory channel's contents to a VFO (or another memory channel). This is useful when searching for signals around a memory channel frequency and for recalling the offset frequency, subaudible tone frequency etc. Pushing and holding [V/M] (SKIP·S. MW) for 2 sec. at the step w, can also copies the memory contents to VFO. In this case, steps e and r are not necessary. D MemoryVFO q Select the memory channel to be copied. Push [V/M] (SKIP·S. MW) momentarily to select memory mode, then rotate [DIAL] to select the desired memory channel. · Select the bank channel with [BAND] (TS·LOCK) and [DIAL], if desired. D Memorymemory q Select the memory channel to be transferred. Push [V/M] (SKIP·S. MW) to select memory mode, then rotate [DIAL] to select the desired memory channel. [. . . ] Operating mode selection While pushing and holding [FUNC], push [CALL] several times to select the desired mode. Audio level setting Push [Y] to increase, push [Z] to decrease the audio level. Squelch level setting While pushing [SQL], rotate [DIAL] to set the squelch level. Frequency band selection Push [BAND] several times, or while pushing and holding [BAND], rotate [DIAL] to select the desired frequency band. Tuning step selection While pushing and holding [FUNC], push [BAND] to enter tuning step selection. [. . . ]