User manual ICOM IC-Q7

[. . . ] INSTRUCTION MANUAL DUAL BAND FM TRANSCEIVER iQ7A iQ7E This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FOREWORD READ ALL INSTRUCTIONS carefully and completely before using the transceiver. CAUTIONS R WARNING!NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm away from the lips and the transceiver is vertical. SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-Q7A/E. R WARNING! [. . . ] Select scan edges in set mode: "ALL" for full scan, "BAND" for band scan or "0P"­"19P" for programmed scan. (see the next page) r Push [FUNC] + [Y] or [Z] momentarily to start the scan. · Decimal point flashes while scanning. · "P SKIP" flashes when the frequency skip function is turned ON. 19) · "0P"­"19P" flash to indicate which pair of scan edges is being scanned. · To change the scanning direction, rotate [DIAL]. · If the pocket beep function is activated, the transceiver automatically selects the tone squelch function when a scan starts. e Select the desired memory bank in set mode, if desired. · See below for details. r Push [FUNC] + [Y] or [Z] momentarily to start the memory scan or memory bank scan. · Decimal point flashes while scanning. · "o" flashes during memory bank scan. · To change the scanning direction, rotate [DIAL]. · If the pocket beep function is activated, the transceiver automatically selects the tone squelch function when a scan starts. t To stop the scan, push [FUNC] + [Y] or [Z] again. D Memory bank selection q Push [V/M] for 2 sec. w Rotate [DIAL] until "BNK SC" appears. e While pushing [FUNC], rotate [DIAL] to select the desired memory bank. · "OFF" scans memories in both banks; "BANK0" scans memories in bank 0 only (ch 0 to 99); "BANK1" scans memories in bank 1 only (ch 100 to 199). t To stop the scan, push [FUNC] + [Y] or [Z] again. If the same frequencies are programmed into a pair of scan edges, programmed scan does not start. For programmed scan, scan edges must be programmed in advance. Program scan edges into regular memory channels and set the channels as scan edges. 17) 16 r Push [V/M] to exit set mode. Memory bank 0 (Memory ch 0 to 99) SCAN OPERATION 6 s Selecting scan edges The scanning range can be set to all frequencies (full scan), a selected band or between two user-programmed frequencies (programmed scan). The programmed scan edges use regular memory channels. Program the desired scan edge frequencies in memory channels in advance. e Rotate [DIAL] until "EDGE" appears. · "EDGE" disappears after 1 sec. and the previously selected scan edge appears. y Push [FUNC] + [Y] to select lefthand scan edge channel. u While pushing [FUNC], rotate [DIAL] to select the desired memory channel which stores a scan edge frequency. · The frequency in the memory channel is displayed for 1 sec. r While pushing [FUNC], rotate [DIAL] to select the desired scan edge. · Select "ALL" for full scan, "BAND" for band scan or "0P"­"19P" for programmed scan. i Push [FUNC] + [Y] to select righthand scan edge channel. o While pushing [FUNC], rotate [DIAL] to select the desired memory channel which stores another scan edge frequency. !0 Push [V/M] to exit set mode. 1 Memory channel frequency is displayed during selection. · Push [FUNC] + [Y] to indicate programmed scan edge for programming other scan edges. [. . . ] · Turn beep tones ON in set mode. · Push [FUNC] + [BAND] to cancel the function. p. Desired set mode item cannot be selected. · The operating mode is not selected correctly. · Select a suitable operating mode in set mode. p. 11 · The desired set mode item is in expanded set mode. [. . . ]