User manual ICOM IC-R2500

[. . . ] INSTRUCTION MANUAL iR2500 COMMUNICATION RECEIVER This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FOREWORD Thank you for purchasing this Icom receiver. The IC-R2500 COMMUNICATIONS RECEIVER is designed and built with Icom's state of the art technology and craftsmanship. With proper care, this receiver should provide you with years of troublefree operation. [. . . ] y Push the same band's [VFO/MR·S. MW] to return to VFO mode. NOTE: Be careful!-- the contents of cleared memories CANNOT be recalled. [EXAMPLE]: Clearing memory channel 20. Push VFO/MR S. MW to select VFO. Push VFO/MR S. MW for 1 sec. Rotate for selecting memory channel. Push SET SKIP three times, then push VFO/MR S. MW for 1 sec. Beep Beep Beep Push any switch for main band other than VFO/MR , then push VFO/MR to return to VFO. S. MW S. MW 29 MEMORY OPERATION 5 Memory bank setting The IC-R2500 has a total of 21 banks (A to H, J to R, T, U, W, Y). Regular memory channels, 0 to 999, may assigned into the desired bank for easy memory management. Push [VFO/MR·S. MW] to select memory mode in the main band, then rotate the same band's [DIAL] to select the desired memory channel. · "!" and memory channel number appear. [SET·SKIP] [VFO/MR·S. MW] [ATT·PRIO] [DIAL] [ 5 w Push and hold the same band's [VFO/MR·S. MW] for 1 sec. to enter select memory write mode. · "!" indicator and the memory channel number blink. r Rotate the same band's [DIAL] to select the desired bank and bank channel. · Push [ATT·PRIO] to toggle the bank or bank channel selection. · Banks A to H, J to R, T, U, W and Y are available. · Only vacant bank channel numbers will be displayed. e Push [SET·SKIP] once to select "bAnk. " After [SET·SKIP] released Bank selection Bank channel selection t Push and hold [VFO/MR·S. MW] for 1 sec. to program the bank and exit select memory write mode. 30 5 MEMORY OPERATION Memory bank selection q Push [VFO/MR·S. MW] to select memory mode in the desired band (left or right). w Push [MHz·TS] to enter memory type selection mode. [VFO/MR·S. MW] [MHz·TS] [DIAL] Transferring bank contents The bank contents of programmed memory channels can be cleared or transferred to another bank. INFORMATION: Even if the bank is cleared of memory channels, the memory channel contents still remain programmed. q Select the desired bank contents to be transferred or erased from the bank in the main band. Push the main band's [VFO/MR·S. MW] several times to select memory mode. Push the same band's [MHz·TS] then rotate the same band's [DIAL] to select the desired memory bank. · Bank's indicator appears at top of the memory channel. e Rotate the same band's [DIAL] to select the desired bank (A to H, J to R, T, U, W or Y). · Only programmed banks are displayed. r Push any key for the main band or any of the shared keys below the display to set the bank indication. · Bank's indicator appears at top of the memory channel. Push any key for the main band or any of the shared keys below the display to select the bank then rotate the same band's [DIAL] to select the desired contents. [VFO/MR·S. MW] [MHz·TS] [DIAL] t Rotate the same band's [DIAL] to select the contents in the bank. y To return to regular memory mode, repeat steps w­r and select "bAnk --" at step e. · Memory bank indication Bank indicator appears 31 MEMORY OPERATION w Push [VFO/MR·S. MW] for 1 sec. to enter select memory write mode. · "!" indicator and the memory channel number blink. 5 r Rotate the same band's [DIAL] to select the desired bank indicator to transfer or erase. · Push [ATT·PRIO] to toggle the bank or bank channel selection. · Select "­ ­" indication when erasing the contents from the bank. · Vacant bank channel numbers are only be displayed. 5 Memory channel blinks e Push [SET·SKIP] once to select "bAnk. " Bank selection Bank channel selection t Push and hold [VFO/MR·S. MW] for 1 sec. to program the bank and return to regular memory mode. y Repeat steps q to t for transferring or erasing an another bank's contents. After [SET·SKIP] released 32 6 SCAN OPERATION Scan types Scanning searches for signals automatically and makes it easier to locate new stations. [. . . ] 41 If your receiver seems to be malfunctioning, please check the following points before sending it to a service center. · The AC adapter is not fully seated in the power · Check the connection. jack on the rear panel. · Rotate [VOL] to obtain a suitable level. No sound comes from the · Volume level is too low. [. . . ]