User manual ICOM IC-R9000L

[. . . ] IP3 performance is +9. 8dBm at 50MHz and +6. 2dBm at 620MHz (+5dBm (typical) from 30MHz to 3335MHz). Digital twin PBT setting example Five roofing filters [dB] 20 0 ­20 ­40 ­60 ­80 ­100 ­120 ­140 SSB sharp filter characteristics Dual DSP The IC-R9000L incorporates two independent, 32-bit floating point DSP units, a dedicated DSP unit for receiver functions and another for the spectrum scope. By using the power of two independent DSP units, the radio can respond to operator changes in an instant. Receiver output [dB] 170 150 130 110 90 70 50 30 10 0 ­10 15MHz Intercept Point +44. 5 dBm ­160 ­4000 ­3000 ­2000 ­1000 0 1000 2000 3000 4000 5000 6000 [Hz] Noise f loor level [dB] 0 FM filter characteristics Dynamic range 109. 2 dB [dBm] Antenna input ­20 ­40 Receiver output [dB] 170 150 130 110 90 70 50 30 10 0 ­10 50MHz Intercept Point +9. 8 dBm ­60 Dual DSP units ­80 ­100 ­120 ­40 ­30 ­20 ­10 0 10 20 30 40 [kHz] ±0. 05ppm high frequency stability Noise f loor level [dBm] Dynamic range 89. 7dB Antenna input Receiver output [dB] 170 150 130 110 90 70 50 30 10 0 ­10 620MHz The IC-R9000L uses an OCXO (Oven Control Cr ystal Oscillator) unit which provides ±0. 05ppm frequency stability from 0°C to 50°C. The 10MHz reference frequency can either be supplied to or input from external equipment. [dB] 20 0 ­20 ­ 40 ­60 ­ 80 AM filter characteristics Intercept Point +6. 2 dBm Noise f loor level ­100 ­120 ­10 Dynamic range 89. 5dB [dBm] Antenna input OCXO unit ­8 ­6 ­4 ­2 0 2 4 6 8 10 [kHz] performance and spectrum analysis SPECTRUM SCOPE Multi function spectrum scope Using a dedicated DSP unit improves the dynamic range of the spectrum scope. [. . . ] The normal spectrum scope covers a range from ±2. 5kHz to ± 5MHz , w hile t he w ide b and spe c tr um scope* observes up to ±500MHz (±10MHz, ±25MHz, ±50MHz, ±100MHz ±250MHz and ±500MHz selectable). When using the nor mal sp e c tr um s c op e, t he digi t al scope's filter width can vary from 200Hz to 20kHz with a variable sweep speed. The spectrum scope can also be set to use specific scope edges or to center the span on the receiving frequency. The peak search function automatically moves the display marker to the strongest signal on the scope screen. In addition to these features, the scope has 3 levels of attenuation (10dB, 20dB, 30dB). * While using the wide band scope function, AF output is muted. · Fixed mode . . . the scope screen does not shift when you change the receiving frequency. the scope screen shifts as the receiving frequency moves. The receiving frequency is always centered on the scope screen. · Wide band scope receives up to ±500MHz. In SQ1 mode, up to 130 minutes (approx. ) of recorded audio can be stored into the CF memory. The other recorder is the shor t voice recorder, which saves the previous 15 seconds of radio audio into RAM, allowing you to play back the audio instantly. Noise blanker The IC-R9000L has the DSP controlled noise blanker that significantly reduces pulse type noise and improves the S/N ratio by removing interfering noise. The noise blanker has two channels with adjustable width and depth parameters. You can use these to target the specific noise interference. FSK modulator & decoder The IC-R9000L has built-in FSK demodulator and decoder. · Twin peak filter · Water-fall indicator · FSK-R mode · FSK tone and shift frequencies programmable Noise reduction The noise reduction function separates signal components from random noise through Digital Signal Processing (DSP) and enhanc es the signals bur ied in noise for improved signal readability. 10 VFOs The IC-R9000L has 10 VFO channels for tuning and storing operating frequencies, mode, filter width and other settings. For example, use VFO-1 for the 7MHz band, VFO-2 for the VHF marine band, Voice recorder setting example ations allowing efficient radio monitoring Multi-scan functions Numerous scanning functions to search for desired stations are a vailable to make operation easier. The IC-R9000L scans 40 channels per second in memory scan mode. · · · · · · · · · Memory scan Program scan Fine program scan F scan /F fine scan Priority scan Selected mode memory scan Selected memory scan Auto memory write scan Tone scan USB connector The IC-R9000L has a USB connector for connecting external USB memory or other USB devices. Received audio and the receiver configuration files can be imported and exported to a PC. Firmware upgrades are also possible via USB memory. · Optional P25 digital mode reception · Optional CI-V inter face and RS-232C for PC remote control · Analog TV tuner (NTSC/PAL/SECAM)*2 * 1 Some functions are not available depending on operating mode or band. *2 Except USA version Additional outstanding features 1 Various receive assist functions* · SSB/CW/AM mode auto tuning function · AFC function compensates for frequency shifts (FM/WFM mode only) · Preamp and attenuator · 1/4 tuning step function and dial click function · CW-R (reverse) mode · APF (Audio Peak Filter) · AGC (Automatic Gain Control) · VSC (Voice Squelch Control) · Input overload protection (HF bands only) · 4 antenna connectors: an SO-239 type, a phono (RCA) connector and two type-N connectors · S/P DIF output jack · Video input/output · Clock function with daily timer and sleep timer · CTCSS and DTCS tone squelch · Simplified frequency calibration using WWV or WWVH · Dial lock function · Panel lock function · Adjustable tuning step · Dimmer function · Monitor function Voice synthesizer The built-in synthesizer announces the receiving frequency, mode and signal strength in English. External Speaker Jack External DC Output Jack (15. 0V) ACC Socket Antenna Selector Jack Reference Frequency In/Out Terminal Speech Output Jack Line Output Jack Recorder Remote Jack Detector Output Jack Video Input Jack Video Output Jack Spare Jack IF Output Jack DC-DC Power Socket Fuse Holder AC Power Socket Main Power Switch Data Input Socket CI-V Remote Control Jack RS-232C Connector External Display Connector Antenna Connector 2 Ethernet Connector Antenna Connector 1/ HF Antenna Connector 3 S/P DIF Output Terminal USB Connector HF Antenna Connector 2 HF Antenna Connector 1 Ground Terminal SPECIFICATIONS GENER AL Frequency coverage (Unit: MHz) France version 0. 005­3335. 000000* * Cellular bands are blocked in the U. S. A. version. RECEIVER Intermediate frequencies HF VHF/UHF 0. 005 ­ 29. 999999 50. 200 ­ 51. 200000 87. 500 ­ 108. 000000 144. 000 ­ 146. 000000 430. 000 ­ 440. 000000 1240. 000 ­ 1300. 000000 58. 7MHz (1st) /10. 7MHz (2nd) /48kHz (3rd) 278. 7MHz or 778. 7MHz (1st) / 58. 7MHz (2nd) /10. 7MHz (3rd)/ 48kHz (4th) SSB, CW, FSK Sensitivity 0. 100 ­ 1. 799MHz*1 1. 800 ­ 29. 999MHz*1 30. 0­2499. 999MHz*2 2500­2999. 999MHz*2 3000­3335. 000MHz*2 0. 5µV 0. 2µV 0. 32µV 0. 32µV 1. 0µV AM 6. 3µV 2. 5µV 3. 5µV 3. 5µV 11µV FM ­ 0. 5µV*3 0. 5µV 0. 5µV 1. 6µV FM50k WFM ­ ­ 0. 71µV*3 ­ 0. 71µV 1. 4µV 0. 71µV 1. 4µV 4. 5µV 2. 2µV Mode Number of memory channels Antenna connectors USB, LSB, CW, FSK, AM, FM, WFM, P25* * Optional UT-122 required. 1220 (1000 regular, 100 auto memory write channels, 100 memory scan skip and 20 scan edges) SO-239 (50 for HF), Phono [RCA] (500 for HF), Type-N × 2 (50 , one each for 30­1149. 99999MHz, 1150 ­ 3335MHz) *1 Preamp1 ON *2 Preamp ON *3 28­29. 999MHz SSB, FSK BW=2. 4kHz, CW BW=0. 5kHz, AM BW=6. 0kHz at 10dB S/N, FM BW=15kHz, FM50k BW=50kHz, WFM BW=180kHz at 12dB SINAD Temperature range Frequency stability Temperature fluctuation Frequency resolution Power supply requirement Power consumption (Representative value) 0°C to +50°C; +32°F to +122°F Less than ±0. 05ppm (at 25°C) after warm up (5 minutes) Less than ±0. 05ppm (0°C to +50°C) 1Hz 100V/120V/230V/240V AC Stand-by Max. [. . . ] audio Less than 100VA Less than 100VA 3rd order IMD dynamic range Selectivity (Representative value) USB, LSB, FSK (BW= 2. 4kHz) CW (BW= 500Hz) AM (BW= 6kHz) FM (BW= 15kHz) WFM 109dB (typ. ) at 14. 1MHz, 100kHz separation, preamp OFF More than Less than More than Less than More than Less than More than Less than More than 2. 4kHz / ­3dB 3. 6kHz / ­60dB 500Hz / ­3dB 700Hz / ­60dB 6. 0kHz / ­3dB 15. 0kHz / ­60dB 12. 0kHz / ­3dB 25. 0kHz / ­60dB 180kHz / ­6dB Dimensions (W×H×D) (projections not included) 424 × 149 × 340 mm; 1611/16 × 5 7/8 × 13 3/8 in 20kg; 44. 1lb (approx. ) Weight Spurious and image rejection ratio Supplied accessories · AC power cable · RCA plugs · Carrying handles · Spare fuses · ACC plugs · DC power plug · Speaker plugs 0. 1 ­ 30. 0MHz 30. 0 ­ 2500MHz 2500 ­ 3000MHz More than 70dB More than 50dB More than 40dB More than 2. 6W with an 8 load All stated specifications are subject to change without notice or obligation. AF output power OPTIONS CT-17 CI-V LEVEL CONVERTER For remote receiver control using a PC with an RS-232C. UT-122 P25 DIGITAL UNIT Provides APCO P25 digital mode reception. SP-20 EXTERNAL SPEAKER 4 audio filters; headphone jack; can connect to 2 receivers. Input power: 5W · All screen images are simulated. · The LCD display may have cosmetic imperfections that appear as small or dark spots. [. . . ]