User manual ICOM IC-RP1220

[. . . ] CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. WORD D FEATURES Wide frequency coverage with all-mode receive Both Remote controller operation and PC control application are available ANF and NR functions are available (Only when the optional DSP unit is installed. ) IF shift function i Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. PRECAUTIONS RWARNING! [. . . ] Up to 100 channels can be assigned to a bank. 5 4 5 Memory channel selection q Push [MR·SKIP] to select memory mode. · "!" indicator appears. D Memory channel contents The following information can be programmed into memory channels: · Operating frequency (p. 10) · Duplex direction (DUP+ or DUP­) with an offset frequency (p. 15) · Tone squelch or DTCS squelch ON/OFF (p. 33) · Tone squelch frequency or DTCS code with polarity (p. 28) [MR·SKIP] "!" appears w Rotate [DIAL] to select the desired memory channel. · Programmed memory channels can only be selected. If memory banks or weather channels* mode appears at step q, push [MR·SKIP] and rotate [DIAL] to select "bAnk --, " then push [MR· SKIP] again to return to channel selection. *Available for USA/CANADA versions only. 16 5 MEMORY OPERATION Programming a memory channel VFO settings, including the set mode contents such as subaudible tone frequency, offset and scan skip information can be programmed into a memory channel. q Push [V/MHz·SCAN] to select VFO mode. wSet the desired frequency using [DIAL]. subaudible tone frequency, scan skip information, etc. ) if required. ePush [S. MW·MW] to enter select memory write mode. · "!" indicator and the memory channel number blink. rRotate [DIAL] to select the desired memory channel to be programmed. · Memory channels not yet programmed are blank. t Push and hold [S. MW·MW] for 1 sec. to program. · 3 beeps sound · Memory channel number automatically increases when continuing to push [S. MW·MW] after programming. CONVENIENT Memory programming can be made quicker by copying memory information to different memory channels (p. 19). [EXAMPLE]: Programming 145. 800 MHz into memory channel 20 (blank channel). Push Rotate for setting frequency, etc. Push . "Beep Rotate Push for 1 sec. NOTE: Be careful!-- the contents of cleared memories CANNOT be recalled. eRotate [DIAL] to select the memory channel to be cleared. [EXAMPLE]: Clearing memory channel 20. Push to select VFO. Rotate for selecting memory channel. Push three times, then push for 1 sec. Push to return to VFO. "" " " " 21 Beep Beep Beep MEMORY OPERATION 5 Memory bank setting The IC-RP1220 has a total of 21 banks (A to H, J to R, T, U, W, Y). Regular memory channels, 0 to 999, may assigned into the desired bank for easy memory management. Push [MR·SKIP] to select memory mode, then rotate [DIAL] to select the desired memory channel. · "!" and memory channel number appear. [ rRotate [DIAL] to select the desired bank and bank channel. · Push [SET·LOCK] to toggle the bank or bank channel selection. · Banks A to H, J to R, T, U, W and Y are available. · Only vacant bank channel numbers will be displayed. 5 Bank selection Bank channel selection wPush [S. MW·MW] to enter select memory write mode. · "!" indicator and the memory channel number blink. e Push [TS·MODE] once to select "bAnk. " tPush and hold [S. MW·MW] for 1 sec. to program the bank and exit select memory write mode. [TS·MODE] After [TS·MODE] released 22 5 MEMORY OPERATION Memory bank selection qPush [MR·SKIP] to select memory mode. wPush [MR·SKIP] again to enter memory type selection mode. Transferring bank contents [ The bank contents of programmed memory channels can be cleared or transferred to another bank. INFORMATION: Even if the bank is cleared of memory channels, the memory channel contents still remain programmed. [DIAL] [MR·SKIP] eRotate [DIAL] to select the desired bank (A to H, J to R, T, U, W or Y). · Only programmed banks are displayed. r Push any key to set the bank indication. · Bank's indicator appears at top of the memory channel. qSelect the desired bank contents to be transferred or erased from the bank. Push [MR·SKIP] to select memory mode. Push [MR·SKIP] again then rotate [DIAL] to select the desired memory bank. t Rotate [DIAL] to select the contents in the bank. [. . . ] to reset the CPU. [SET·LOCK] [PWR] [S. MW·MW] 47 OTHER FUNCTIONS 10 Internal audio switch The internal switch must be set properly to use an external speaker, headphones or earphone. Before removing the top cover, turn the receiver power OFF, then disconnect the DC power cable. q Turn the power OFF, then disconnect the DC power cable. wUnscrew the 8 screws and disconnect the connected cables, then remove the top cover. · Be careful not to lose the screws. [. . . ]