User manual ICOM IC-RP1620

[. . . ] With proper care, this product should provide you with years of trouble-free operation. We want to take a moment of your time to thank you for making your IC-RP1620 your radio of choice, and hope you agree with Icom's philosophy of "technology first. " Many hours of research and development went into the design of your IC-RP1620. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the receiver. SAVE THIS INSTRUCTION MANUAL-- This instruction manual contains important operating instructions for the IC-RP1620. EXPLICIT DEFINITIONS WORD R DANGER!CAUTION NOTE DEFINITION Personal death, serious injury or an explosion may occur. Personal injury, fire hazard or electric shock may occur. [. . . ] Scan link name or scan name is not displayed during scan. Selectable between "0" to "9" if programmed (p. 53) · Band scan · Program scan Selectable between "0" to "24" if programmed (p. 30) 29 SCAN OPERATION 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Scan edges programming Scan edges can be programmed in the same manner as memory channels. Scan edges are programmed into scan edge memory channels, 00A/00B to 24A/24B. w Set a desired frequency: Push [BAND] to select a desired band. Rotate [DIAL] to set a desired frequency. frequency offset, duplex direction, tone squelch, etc. ), if desired. e Hold down [S. MW](V/M) for 1 second to enter the select memory write mode. · 1 short and 1 long beep sounds. · The " " icon and memory channel number blink. r Rotate [DIAL] to select a desired programmed scan edge channel from 00A to 24A. t Hold down [S. MW](V/M) for 1 second. · 3 beeps sound · The matched "B" channel is automatically selected if you continue to hold down [S. MW](V/M) after programming. y To program a frequency for the other pair of scan edges, 00B or 24B, repeat steps w and t. · If the same frequency is programmed into a pair of scan edges, the programmed scan will not function. [EXAMPLE]: Programming 145. 370 MHz into scan edge channel 03A (a blank channel). Rotate to select channel 03A. The VFO mode Enter the select memory write mode. Hold down [SCAN](MODE) for 1 second to enter the scan type selection mode. Rotate [DIAL] to select a desired scanning type. · Select "ALL" for full scan, "BAND" for band scan, "P-LINK x" for programmed link scan (x= 0 to 9), "PROGxx" for programmed scan (xx= 0 to 24; only programmed scan edge numbers are displayed). D During auto memory write scanning: · When a signal is received, the scan pauses for approximately 5 seconds and the frequency is stored into an auto memory write channel group (AW000­AW199). - 2 short beeps sound when stored. · The scan resumes after frequency storing. · When all channels are stored, the scan automatically stops and 1 long beep sounds. 6 D Re-calling the stored frequencies: q Push [V/M] to select the memory mode. w Push [BAND] repeatedly, or while holding down [BAND], rotate [DIAL], to select the auto memory write channel group. · "AW" appears. Push [SCAN](MODE) to start the scan. w Push [V/M] to turn the auto memory write function ON or OFF. · The " " icon blinks. · Push [SCAN](MODE) to stop the scan. [DIAL] During auto memory write scan e Rotate [DIAL] to select a desired channel. "AW" appears when the auto memory write channel group is selected. D Clearing the stored frequencies: q Select the auto memory write channel group. w While holding down [FUNC], push and hold [S. MW](V/M) for 1 second to clear all the channels' contents. · 1 short and 1 long beep sounds. The " " icon blinks during auto memory write scan. NOTE: The auto memory write channel contents CANNOT be cleared by an independent channel. Thus it is a good idea to copy the contents into a regular memory channel. 34 6 SCAN OPERATION Skip channel/frequency setting Memory channels can be set to be skipped for a memory skip scan. In addition, memory channels can be set to be skipped for both a memory skip scan and a frequency skip scan. [. . . ] · CT-17 ci-v level converter For receiver remote control using a PC. Approved Icom optional equipment is designed for optimal performance when used with an Icom receiver. Icom is not responsible for the destruction or damage to an Icom receiver in the event the Icom receiver is used with equipment that is not manufactured or approved by Icom. 79 q Cut w Fold e Complete POCKET GUIDE 16 Important operating instructions are summed up on this and the following page for your simple reference. By cutting along the line and folding on the dotted line, it will become a card sized operating guide which can easily be carried in a card case or wallet, etc. iR6 VFO and memory mode selection Push [V/M] to toggle between the VFO and the memory mode. Receive mode selection Push [MODE] repeatedly to select a desired mode. [. . . ]