User manual ICOM IC-RP2210

[. . . ] With proper care, this product should provide you with years of trouble-free operation. We want to take a couple of moments of your time to thank you for making your IC-RP2210 your radio of choice, and hope you agree with Icom's philosophy of "technology first. " Many hours of research and development went into the design of your IC-RP2210. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the receiver. SAVE THIS INSTRUCTION MANUAL-- This instruction manual contains important operating instructions for the IC-RP2210. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric R WARNING!CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. [. . . ] · Rotate [DIAL] to select the channel. · Push [HOLD V] again to restart the scan. The category/group link setting can be changed in memory programming. Scan skips any memory channels in the selected category/group/name that are set to "SKIP" or "PSKIP. " (pgs. 52­54) Link scan stops at the first channel when all channels in a category/group are set to "SKIP" or "PSKIP. " (pgs. 52­54) · Scan mode indication DIAL NO. MENU CLR HOLD V SCAN SQL MW ENT HOLD V SCAN SEARCH 1 4 2 5 8 0 3 6 9 SKIP IMPORTANT!: To perform scan functions, 2 or more memory channels MUST be programmed, otherwise the scans will not start. . 7 ATT Arrow indicates scanning direction 6 SEARCH AND SCAN OPERATIONS All scan All scan repeatedly scans all memory channels programmed with any frequencies in the memory channel selected for scanning. q Enter "ALL SCAN" in SCAN menu. MENU SCAN ALL SCAN (Push [MENU ]), (Push [r]/[s], then push [ENT MW]. ) · SCAN menu can also be entered by pushing and holding [SCAN] for 1 sec. · Scan pauses when a signal is received. · Rotate [DIAL] to change the scanning direction. Category scan Category scan repeatedly scans all memory channels in the same category as the selected memory channel has been programmed. q Enter "CATEGORY SCAN" in SCAN menu. MENU SCAN CATEGORY SCAN (Push [MENU ]), (Push [r]/[s], then push [ENT MW]. ) · SCAN menu can also be entered by pushing and holding [SCAN] for 1 sec. w Push [HOLD V] to stop the scan temporarily, if desired. · Push and hold [v] or [w] for 1 sec. · Search, scan or priority watch operation can also be selected. Memory category/group/name can be set to be skipped during scan operation. In addition, memory channels can be set to be skipped during search or scan operation. This is useful to speed up the search or scan rate. MENU SCAN SKIP (Push [MENU ]), (Push [r]/[s], then push [ENT MW]. ) · SCAN menu can also be entered by pushing and holding [SCAN] for 1 sec. y When the alert is detected, a beep sounds and the following indication will be displayed. u Turn the weather alert function OFF in SCAN menu. NOTE: While receiving a signal (on a frequency other than the weather alert ON frequency), the receiving signal or audio will be interrupted momentarily every 5 sec. (approx. ) in the case that the alert function is turned ON. This symptom is caused by the WX alert function. To cancel these symptoms, set the weather alert item OFF in SCAN menu. MENU DIAL NO. MENU CLR SQL MW ENT HOLD V SCAN SEARCH 1 4 2 5 8 0 3 6 9 SKIP MW ENT ENT Push MW . 7 ATT 6 SEARCH AND SCAN OPERATIONS w Push [v]/[w] once or twice to to select "CATEGORY, " "GROUP" or "NAME. " CONVENIENT!(Group skip setting) The group skip setting can be set with the following operation during a scan or scan holding state. q Select the desired memory group to be skipped. Push [SCAN] to start a scan, then push [HOLD V] to hold the scan. [. . . ] Sensitivity is low and only · The attenuator function is activated. · Receiving mode is not selected correctly. p. 2, 3 · Push and hold [· ATT] for 1 sec. · Set the RF gain to "MAX" in SETTING menu. [. . . ]