User manual ICOM IC-RP4520

[. . . ] With proper care, this product should provide you with years of trouble-free operation. We want to take a couple of moments of your time to thank you for making your IC-RP4520 your radio of choice, and hope you agree with Icom's philosophy of "technology first. " Many hours of research and development went into the design of your IC-RP4520. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the receiver. SAVE THIS INSTRUCTION MANUAL-- This instruction manual contains important operating instructions for the IC-RP4520. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock R WARNING!CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. [. . . ] Set the desired frequency with [R-DIAL]. Or set the desired frequency with [KEYPAD]. offset frequency, duplex direction, tone squelch, etc. ), if desired. to select the select memory write condition. · 1 short and 1 long beep sound. µ · "µ " indicator blinks. D Memory channel contents The following information can be programmed into memory channels: · Operating frequency (p. 16) · Duplex direction (+DUP or ­DUP) with an offset frequency (p. 20) · Tone squelch or DTCS squelch ON/OFF (p. 45) · Tone squelch frequency or DTCS code with polarity (p. 39) 5 6 r Rotate [R-DIAL] to select the desired channel. · Scan edge channel, 00A/B to 24A/B can also be selected. t Push [MR S. MW] for 1 sec. · 3 beeps sound · Memory channel number automatically increases when continuing to push [MR S. MW] after programming. [EXAMPLE]: Programming 145. 870 MHz into memory channel 20 (blank channel). Push -DUP TSQL MODE FM ANL MR S. MW for 1 sec. FM Rotate FM Push ---------------µ 020 . -BANK :---BANK-:----BNAME: -MNAME: MNAME: -SKIP :OFF SKIP-:OFF >CLEAR CLEAR MR S. MW for 1 sec. -DUP TSQL MODE FM ANL AFC 145 870 µ 001 PSKIP -BANK :---BANK-:----BNAME: -MNAME: MNAME: -SKIP :OFF SKIP-:OFF >CLEAR CLEAR 146. 010 µ . AFC 001 145 870 µ 020 PSKIP -DUP TSQL MODE FM ANL AFC 145 870 µ 020 PSKIP 26 6 MEMORY CHANNELS Memory bank setting The IC-RP4520 has a total of 26 banks (A to Z). Regular memory channels, 000 to 999, are assigned into the desired bank for easy memory management. Therefore, the previously programmed bank name will be displayed when bank name indication is selected. Also, the programmed bank name is assigned for the other bank channels automatically. 29 MEMORY CHANNELS D Available characters 6 ABCDEFGHIJKLMNOP QRSTUVWXYZ abcdefghijklmnop qrstuvwxyz 0123456789 Ò¨Î!"#$%&'()*+, -. /:;<=>?@[\]^_{ |}~ 01243 (space) Selecting memory/bank name indication During memory mode operation, one of the programmed memory name or bank name can be displayed below the frequency indication. -DUP TSQL MODE FM ANL AFC [R-DIAL] B:GROUP1 145 700 µ 012 PSKIP 6 ATT -DUP TSQL MODE FM ANL AFC M. N 6 M:Ricky 145 700 µ 012 PSKIP When no memory or bank name is programmed with the selected memory channel, no indication is displayed. -DUP TSQL MODE FM ANL AFC B:GROUP1 145 700 µ 012 PSKIP q Push [MR S. MW] to select memory mode. · Push [BAND] several times to select the desired bank group. wWhile pushing [6 M. N], rotate [R-DIAL] to select display indication type from bank name or memory name. 30 6 MEMORY CHANNELS Copying memory contents This function transfers a memory channel's contents to VFO (or another memory channel). This is useful when searching for signals around a memory channel frequency and for recalling the offset frequency, subaudible tone frequency etc. at the step w, will also copy the memory contents to VFO. In this case, the steps e and r are not necessary. D MemoryVFO q Select the memory channel to be copied. Push [MR S. MW] to select memory mode, then rotate [R-DIAL] to select the desired memory channel. · Select the bank channel with [BAND] and [R-DIAL], if desired. D Memorymemory q Select the memory channel to be copied. Push [MR S. MW] to select memory mode, then rotate [RDIAL] to select the desired memory channel. to select the select memory write condition. · 1 short and 1 long beep sound. µ · "µ " indicator blinks. · Do not hold [MR S. MW] for more than 1 sec. [. . . ] 91 q Cut w Fold e Complete POCKET GUIDE 18 Important operating instructions are summed up in this and the following page for your simple reference. By cutting along the line and folding on the dotted line, it will become a card sized operating guide which can easily be carried in a card case or wallet, etc. iR20 VFO mode selection Push [VFO MHz] momentarily to select VFO mode. Memory mode selection Push [MR S. MW] momentarily to select memory mode. Receive mode selection Push [MODE SCAN] several times to select the desired mode. [. . . ]