User manual ICOM IC-T90A

[. . . ] INSTRUCTION MANUAL MULTIBAND FM TRANSCEIVER iT90A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIO TELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. FOREWORD Thank you for purchasing this Icom product. The IC-T90A MULTIBAND TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. [. . . ] · Blank channels can be selected via keypad. · Previously selected channels appear when the wrong memory channel number is entered. [DIAL] D Selecting with tuning dial q Push [MR] to select memory mode. w Rotate [DIAL] to select the desired memory channel. Memory mode indication FM CONVENIENT The memory channels (000­099) can be selected with 1 or 2 digits plus [MR]. · Selecting memory channel 005. Push [2], [4] and [MR]. t MEMORY/CALL CHANNELS 36 Appears Memory channel number D Check contents of all memory channels q Push [MR S. MW] for 1 sec. to enter memory write condition. · Memory channel readout blinks. FM D Selecting with keypad q Push [MR] to select memory mode. w Push the desired numeral keys to select the desired memory channel. [MR S. MW] · Selecting memory channel 001. Push [4], [9] and [9]. V 1 4 7 D TONE 2 5 8 H/L 3 6 9 TS keypad 0 w Rotate [DIAL] to check the desired memory channel. Rotating [DIAL] while pushing [BAND] also selects all memory channels. DUP SKIP M. N RIT T. SCAN SET 5 MEMORY/CALL CHANNELS I Programming memory channels Program the desired frequency into a memory channel, call channel or scan edge channel as follows. The memory channels are shared with all bands. Memory channels 003­499 are blank (non-programmed) channels as a factory setting. [DIAL] D Programming a memory channel [EXAMPLE]: 433. 520 MHz into Mch 11 q Select VFO mode with [VFO]. w Set the desired frequency: Select the desired band with [BAND]. offset frequency, duplex direction, subaudible tone frequency, etc. ), if required. to indicate memory channels. · Memory channel indicator " " and channel readout blinks. · Do not hold [MR S. MW] for more than 2 sec. , otherwise the previously selected memory channel contents will be overwritten. [BAND] [VFO] [MR S. MW] r Rotate [DIAL] to select the desired channel. · Call channels (C0­C4), VFO (VF) and scan edge channels (0A/0B­24A/24B), as well as regular memory channels, can be programmed in this way. t Push [MR S. MW] for 1 sec. to program. q, w Set the frequency. FM P SKIP e Push [MR S. MW] for 1 sec. FM r Select the desired channel. t Push [MR S. MW] for 1 sec. FM P SKIP " " and memory channel readout blinks. VFO mode is selected after writing. 37 MEMORY/CALL CHANNELS 5 D Auto memory channel increment While programming a memory channel, the next memory channel can be selected automatically. This is convenient when programming memory channels one after another. or more, at step t of the left section, to select the next memory channel automatically. Push [MR S. MW] for 1 sec. FM I Transferring memory contents to VFO This is convenient when operating around a memory or call channel. t MEMORY/CALL CHANNELS 38 q Push [VFO] several times to select VFO A or B to be transferred. e Set the desired memory channel with [DIAL]. · Call or scan edge channel contents can be transferred in the same manner. Select a call channel in this case. Keep pushing [MR S. MW]. FM P SKIP r Push [MR S. MW] for 2 sec. [EXAMPLE]: Transferring memory channel 26 to VFO A. [DIAL] Select the desired Mch. FM DUP T Next memory channel is automatically selected. VFO is selected. FM P SKIP MR S. MW for 2 sec. P SKIP Transfer to VFO. FM DUP T [MR] 5 MEMORY/CALL CHANNELS I Copying memory contents This is convenient when programming memory contents into a scan edge channel or call channel. · Call or scan edge channel contents can be copied in the same manner. I Memory names Each memory, scan edge and call channels can be programmed with an alphanumeric name such as a repeater name, club name, etc. , for easy recognition. Names can be a maximum of 6 characters--see the table at right for available characters. q Push [MR S. MW] to select memory mode. [. . . ] e Push [8 SET] momentarily, then rotate [DIAL] to change the setting. r Push [8 SET] momentarily to return to the condition of step w. t Push [VFO] to exit the SET mode. I Cancelling skip setting I CPU reset operation MULTIBAND TRANSCEIVER q Select TV channel mode. w While pushing [BAND], rotate [DIAL] to select desired skip channel. [. . . ]