User manual ICOM IC-V8000

[. . . ] INSTRUCTION MANUAL VHF FM TRANSCEIVER iV8000 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FOREWORD Thank you for purchasing this Icom product. The IC-V8000 VHF FM TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. [. . . ] i Push [V/MHz(SCAN)] to program the name and exit the channel name programming condition. to return to frequency indication if desired. 5 q Push [M/CALL(PRIO)] to select memory mode. w Rotate the tuning dial to select the desired memory channel. to select channel name indication mode. · 1 short and 1 long beep sound. IMPORTANT!: Once channel name indication mode is selected, always access the channel name programming condition when [SET(LOCK)] is pushed. When set mode accessing is necessary, cancel the channel name indication by pushing [MONI(ANM)] for 1 sec. , then access to set mode. SET Push LOCK or the cursor. MW S. MW [EXAMPLE]: Programming "CLUB" into memory channel 1. Select memory channel 1, then push MONI for 1 sec. Push V/MHz SCAN . 30 5 MEMORY OPERATION Channel names can also be programmed via the microphone. z Select the memory/call channel to be assigned memory names. Push [MR/CALL] to select memory mode, then select the desired memory channel via [Y]/[Z] or keypad. · Scan edge channels can also be selected. Push [MR/CALL] for 1 sec. x Push [FUNC], then [MONI 1(ANM)] momentarily. c Push [SET B(D-OFF)]. · Frequency readouts disappear. b Push [SET B(D-OFF)] or [ENT C(T-OFF)] to move the cursor to left or right, respectively. n Repeat steps v and b until the desired channel names are displayed. m Push [CLR A(MW)] to program the name and exit the channel name programming condition. , Push [FUNC], then push [MONI 1(ANM)] to return to frequency indication if desired. v Push [Y]/[Z] to select the desired character. · The selected character blinks. [EXAMPLE]: Programming "CLUB" into memory channel 1. Select memory channel 1, push , then push . Push . Push to select the character. 31 MEMORY OPERATION 5 I Memory bank selection q Push [M/CALL(PRIO)] to select memory mode, if desired. w Push [BANK(OPT)] to select memory bank condition. · Bank initial blinks BANK/OPTION Push [BANK(OPT)] to select memory bank mode. z Push [MR/CALL] to select memory mode, if desired. x Push [BANK/OPTION] to select memory bank condition. · Bank initial blinks 5 e Rotate the tuning dial to select the desired bank, A to J. · Banks that have no programmed contents are skipped. [Y]/[Z] c Push [Y]/[Z] to select the desired bank, A to J. · Only programmed memory bank can be selected. r Push [BANK(OPT)] to set the bank. · Initial stops blinking. v Push [BANK/OPTION] to set the bank. · Initial stops blinking. t Rotate the tuning dial to select the contents in the bank. · No channel numbers are displayed for memory bank operation. b Push [Y]/[Z] to select the desired contents in the bank. · No channel numbers are displayed for memory bank operation. n To return to regular memory condition, push [BANK/OPTION] twice. y To return to regular memory condition, push [BANK(OPT)] twice. 32 5 MEMORY OPERATION I Memory bank setting q Push [M/CALL(PRIO)] to select memory mode, then select the desired memory channel via the tuning dial. w Push [BANK(OPT)]. · "­ ­" indication blinks as follows. MW BANK/OPTION z Push [MR/CALL] then select the desired memory channel via [Y]/[Z] or keypad. x Push [BANK/OPTION]. · "­ ­" indication blinks. c Push [BANK/OPTION] again to set the channel to bank setting stand-by condition. · "­ ­" indication stops blinking. [Y]/[Z] e Push [BANK(OPT)] again to set the channel to bank setting stand-by condition. · "­ ­" indication blinking stops. v Push [FUNC] then [CLR A(MW)] then push [Y]/[Z] to select the desired bank to be set. · "M" and bank initial blink. r Push [MW(S. MW)] then rotate the tuning dial to select the desired bank to be set. · "M" and bank initial blink as follows. b Push [CLR A(MW)] to set the channel into the bank. · "M" and bank initial stops blinking. n Push [BANK/OPTION] twice to return to regular memory channel condition. m Repeat steps z to n to set an another memory channel into the same or another bank. t Push [MW(S. MW)] again to set the channel into the bank. · "M" and bank initial blinking stops. y Push [BANK(OPT)] twice to return to regular memory condition. u Repeat steps q to y to set another memory channel into the same or another bank. 33 MEMORY OPERATION 5 I Transferring bank contents Contents of programmed memory banks can be cleared or transferred to another bank. [. . . ] · Only 1 memory channel is programmed or other · Program other memory channels or cancel the pgs. 25, 26, 41 channels are set as skip channels. memory skip function in the desired channels. 44 · Priority watch is activated. [. . . ]