User manual ICOM IC-W32E

[. . . ] INSTRUCTION MANUAL DUAL BAND FM TRANSCEIVER iC-w32a iC-w32e This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. CAUTIONS RWARNING!NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 in) away from the lips and the transceiver is vertical. SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-W32A and IC-W32E. RWARNING! [. . . ] version only), this selection and step r are not necessary. 21) 5 Some repeaters require DTMF tones or a 1750 Hz tone to be accessed. In this case, perform the following instead of step r at left with the required tone. DTMF TONES (IC-W32A only) While pushing [PTT], push the desired digit key(s) to transmit DTMF tones. · The transceiver has 4 DTMF memory channels. 26 for details. r Push [TONE] to activate the subaudible tone encoder, according to repeater requirements. · Refer to the next page for tone frequency settings. 1750 Hz TONE (Europe, Italy and U. K. versions only) While pushing [PTT], push and hold [CALL] for 1 to 2 sec. to transmit a 1750 Hz tone burst signal. · Pushing [PTT] 2 times quickly also transmits a 1750 Hz tone. Release [PTT] briefly, then push [PTT] again to talk in this case. t Push and hold [PTT] to transmit. · The displayed frequency automatically changes to the transmit frequency (repeater input frequency). · If "oFF" appears, check the offset frequency. u Push and hold [SQL] to check whether the other station's transmit signal can be directly received or not. CONVENIENT Tone scan function: When you don't know the subaudible tone used for a repeater, the tone scan is convenient for detecting the tone frequency. 19 5 REPEATER OPERATION s Subaudible tones Some repeaters require subaudible tones to be accessed. Subaudible tones are superimposed over your normal signal and must be set in advance. USING s Offset frequency When communicating through a repeater, the transmit frequency is shifted from the receive frequency by an amount determined by the offset frequency. USING SET MODE SET MODE SETTING SUBAUDIBLE TONES MAIN MAIN SETTING AN OFFSET FREQUENCY MAIN MAIN T T 88. 5 Hz tone 254. 1 Hz tone 0. 6 MHz (600 kHz) offset 5. 0 MHz offset q Push [(H/L)SET] for 2 sec. w Push [(H/L)(SET)J] or [(TONE)K] several times until "RT" appears as shown above. e Rotate [DIAL] to select the desired subaudible tone. · Each operating band for each display and each memory channel have independent settings. r Push [(VFO)CLR] to set the condition and to exit set mode. · Subaudible tone frequency list 67. 0 69. 3 71. 9 74. 4 77. 0 79. 7 82. 5 85. 4 88. 5 91. 5 94. 8 97. 4 100. 0 103. 5 107. 2 110. 9 114. 8 118. 8 123. 0 127. 3 131. 8 136. 5 141. 3 146. 2 151. 4 156. 7 159. 8 162. 2 165. 5 167. 9 171. 3 173. 8 177. 3 179. 9 183. 5 186. 2 189. 9 192. 8 196. 6 199. 5 q Push [VFO] to select VFO mode. e Push [(H/L)(SET)J] or [(TONE)K] several times until "OW" appears as shown above. r Rotate [DIAL] to select the desired offset (separately selectable for each band). · Pushing [(VFO)MHz] for 2 sec. selects MHz steps. (Unit: Hz) 203. 5 206. 5 210. 7 218. 1 225. 7 229. 1 233. 6 241. 8 250. 3 254. 1 t Push [(VFO)CLR] to set the condition and to exit set mode. 20 REPEATER OPERATION 5 s Auto repeater function (U. S. A. version automatically activates the repeater settings (duplex ON/OFF, duplex direction, tone encoder ON/OFF) when the operating frequency falls within or outside of the general repeater output frequency range. The offset and repeater tone frequencies are not changed by the auto repeater function, reset these frequencies, if necessary. · Frequency range and offset direction FREQUENCY RANGE 145. 200­145. 495 MHz 146. 610­146. 995 MHz 147. 000­147. 395 MHz 442. 000­444. 995 MHz USING DUPLEX DIRECTION "­DUP" appears "DUP" appears­ "DUP" appears­ "­DUP" appears Initial set mode 447. 000­449. 995 MHz SETTING THE AUTO REPEATER FUNCTION Activates for duplex only. Activates for duplex and tone. q Turn power ON while pushing [(H/L)SET] to enter initial set mode. w Push [(H/L)(SET)J] or [(TONE)K] several times until "AR" appears as shown above. [. . . ] · Memory mode or call channel is selected. · Lock function is activated. · Scan does not start. · The squelch is open. · Call or weather channel (U. S. A. only) is selected. 39 12 MODE ARRANGEMENT SET J H/L MAIN BAND Although the following chart refers mainly to the VHF (right) band, the same arrangement applies to the UHF (left) band (except commonly used mode, DTMF memory, SCAN SET and INITIAL SET). (push for 2 sec. ) VFO MAIN MAIN DTMF·M · VFO (push for 2 sec. ) VFO MODE MR VFO CALL VFO DTMF MEMORY MODE DTMF MEMORY CHANNEL MEMORY MODE (FREQUENCY INDICATION) MAIN M·N MR MAIN CALL CHANNEL MODE MAIN DTMF·M · VFO (push for 2 sec. ) CALL (CHANNEL NAME INDICATION) DTMF MEMORY PROGRAMMING 40 MODE ARRANGEMENT INITIAL SET MODE 12 SCAN DT SET J H/L + Power ON SET J H/L DUP K TONE MF MAIN SET MODE SET J H/L MAIN + Power ON DUP K TONE SET J H/L SCAN SET MODE DUP K TONE Frequency skip function (p. [. . . ]