User manual ICOM ID-1

[. . . ] INSTRUCTION MANUAL DIGITAL TRANSCEIVER ID-1 DIGITAL TRANSCEIVER ID-1 MIC TD/RD PWR TX/RX POWER FOREWORD Thank you for purchasing this Icom product. The ID-1 DIGITAL is designed and built with Icom's superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. TRANSCEIVER IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. We want to take a couple of moments of your time to thank you for making your ID-1 your radio of choice, and hope you agree with Icom's philosophy of "technology first. " Many hours of research and development went into the design of your ID-1. SAVE THIS INSTRUCTION MANUAL-- This instruction manual contains important operating instructions for the ID-1. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock R WARNING!CAUTION NOTE Equipment damage may occur. [. . . ] Refer to page 60 for offset frequency setting. r Click [TONE] to turn the repeater tone encoder ON. · "TONE" appears. Refer to page 59 for tone frequency setting. NOTE for the USA version: During the auto repeater function ON, the steps e and r are not necessary, depending on the settings. See page 106 for the auto repeater function. Displays transmit frequency. Appears during transmit. y Release [PTT] to receive. uClick [MONI] to check whether the other station's transmit signal can be received directly. iTo return to simplex operation, click [RP] several times to clear the "RP­" or "RP+" indicator. oTo turn OFF the repeater tone encoder, click [TONE] several times until no tone indicators appear. Appear Click 57 REPEATER OPERATION-- VOICE 8 D Setting from the RC-24 q Push [MODE] to select FM mode. · "FM" appears. t Push and hold [PTT] to transmit. · The display frequency automatically changes to the transmit frequency (repeater input frequency). · If the repeater indicator, "RP-" or "RP+" blinks, confirm that the offset frequency (p. 60) is set correctly. wSet the desired receive frequency (repeater output frequency). e Push [RP·4] several times to select minus or plus duplex. · "RP-" or "RP+" appears. Refer to page 60 for offset frequency setting. y Release [PTT] to receive. During receive rPush [TONE· ·5] to turn the repeater tone encoder ON. LOW · "TONE" appears. Refer to page 59 for tone frequency setting. 1294. 500 FM RP- TONE During transmit 00 LOW NOTE for the USA version: During the auto repeater function ON, the steps e and r are not necessary, depending on the settings. See page 106 for the auto repeater function. [TONE· ·5] [RP·4] 8 1282. 500 FM RP- TONE 00 [MODE] LOW 1294. 500 FM RP- TONE 00 uPush and hold [SQL] to check whether the other station's transmit signal can be received directly. iTo return to simplex operation, push [RP·4] several times to clear the "RP-" or "RP+" indicator. oTo turn OFF the repeater tone encoder, push [TONE· ·5] several times until no tone indicators appear. 58 8 REPEATER OPERATION-- VOICE I Repeater tone frequency setting D Setting from the application qDisplays set mode screen by performing one of the following operations. - Select "Edit SetMode(C). . . " in view menu. - Click " " button in tool bar. wDouble click "Repeater Tone" frequency cell, then select the desired frequency from the displayed list. · To close the screen, click " " or repeat the operation as step q. Double click D Setting from the RC-24 q Push [MODE] several times to select FM mode. ePush [MODE] or [TXinh· ] to select "Repeater Tone" item. r Rotate [DIAL] to select the desired tone frequency. · See the table below for the available frequencies. t Push [PWR] momentarily to exit set mode. [DIAL] [TXinh· ] [MODE] LOW Appears 88. 5 Repeater Tone · Available tone frequencies (unit: Hz) 171. 3 173. 8 177. 3 179. 9 183. 5 186. 2 189. 9 192. 8 196. 6 199. 5 203. 5 206. 5 210. 7 218. 1 225. 7 229. 1 233. 6 241. 8 250. 3 254. 1 Select from the above list. 67. 0 69. 3 71. 9 74. 4 77. 0 79. 7 82. 5 85. 4 88. 5 91. 5 94. 8 97. 4 100. 0 103. 5 107. 2 110. 9 114. 8 118. 8 123. 0 127. 3 131. 8 136. 5 141. 3 146. 2 151. 4 156. 7 159. 8 162. 2 165. 5 167. 9 59 REPEATER OPERATION-- VOICE 8 I Offset frequency setting D Setting from the application qDisplays set mode screen by performing one of the following operations. - Select "Edit SetMode(C). . . " in view menu. [. . . ] No contact possible with · The other station is using tone squelch. · The transceiver is set to duplex. · Turn the tone squelch function ON. 74­76 · Correct the offset frequency. [. . . ]