User manual IDEAL ND2366

[. . . ] #61-482 Symbols in this Manual This symbol indicates where cautionary or other information is found in the manual. Fuse Battery Refer to Figure 1 and to the following numbered steps to familiarize yourself with the meter's front panel controls and connectors. 480 Platinum Pro Series Commercial Contractor Grade Multimeter 1 9 10 8 7 11 12 2 True RMS True RMS 4 3 5 6 2 1. Digital Display ­ The digital display has 4000 counts LCD readout with 82 segments analog bar graph, auto polarity, decimal point, " " AC, DC RANGE, H APO and unit annunciators. Rotary Switch ­ Select the Function and Range desired. [. . . ] Set the rotary switch to the V position. Push the blue button until AC is shown on the display. Connect the meter in parallel with the load or circuit. Measure AC Voltage. 5 6 DC Volts Circuit Connection: True RMS AC Current Circuit Connection: True RMS True RMS Range 400mV 4V 40V 400V 1000V Resolution 100µV 1mV 10mV 100mV 1V Max Display Accuracy 400. 0 ±(0. 25% +5) 4. 000 ±(0. 4% +1) 40. 00 ±(0. 25% +1) 400. 0 1000 Range 40mA 400mA 10A Resolution 10µA 0. 1mA 10mA Max 40. 00 400. 0 10. 00 Accuracy Voltage Display Burden ±(2. 0% +5) 200mV max 2Vmax ±(2. 5% +5) 2V max Input Impedance: 10M (over 1000M in 400mV range) To Measure DC Voltage: 1. Plug the black test lead into the COM port and the red test lead into the °C°F VHz port. Set the rotary switch to the V position. Push the blue button until DC is shown on the display. Connect the meter in parallel with the load or circuit. Measure DC Voltage AC Conversion Type: AC conversions are AC-coupled, true RMS responding, calibrated to the RMS value sine wave input. Overload Protection: 1A (500V) fast blow fuse for mA input 16A (500V) fast blow fuse for A input Crest Factor: +1. 5% additional error for C. F. from 1. 4 to 3 +3. 0% additional error for C. F. from 3 to 4 To Measure True RMS AC Current: 1. Plug the black test lead into the COM port and the red test lead into the mA or A port. Set the rotary switch to the mA or A position. Push the blue button until AC is shown on the display. Connect the meter in series with the load or circuit. 8 7 DC Current Circuit Connection: Frequency/RPM Circuit Connection: True RMS True RMS Range 40mA 400mA 10A Resolution 10µA 0. 1mA 10mA Max Display 40. 00 400. 0 10. 00 Voltage Burden ±(0. 6% +2) 200mVmax ±(0. 7% +2) 2Vmax ±(1. 0% +3) 2V max Accuracy Range 4. 0KHz/40KRPM 40KHz/400KRPM 400KHz/4MRPM 4MHz/40MRPM 40MHz/400MRPM Resolution 1Hz/30RPM 10Hz/300RPM 100Hz/3KRPM 1KHz/30KRPM 10KHz/300KRPM Sensitivity 100mV rms* Accuracy Frequency: 0. 01% ±1 digit 250mV rms IV rms RPM: 0. 01% ±10 digits Overload Protection: 1A (500V) fast blow fuse for mA input 16A (500V) fast blow fuse for A input To Measure DC Current: 1. Plug the black test lead into the COM port and the red test lead into the mA or A port. Set the rotary switch to the mA or A position. Push the blue button until DC is shown on the display. Connect the meter in series with the load or circuit. Measure DC Current. Overload Protection: 600V rms *Less than 20Hz the sensitivity is 1. 5V To Measure Frequency: 1. [. . . ] Remove the probe tips from the end of the leads. Set the rotary switch to the V position. Push the blue button until AC is shown on the display. Snap the jaw of the current clamp around one of the current carrying conductors. C 19 20 Maintenance Warning To avoid electrical shock, remove test lead before opening the cover. [. . . ]