User manual IIYAMA PROLITE T1532SR

[. . . ] USER MANUAL ENGLISH Thank you very much for choosing the iiyama LCD monitor. We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference. ENGLISH CE MARKING DECLARATION OF CONFORMITY This LCD monitor complies with the requirements of the EC Directive 2004/108/EC "EMC Directive" , 2006/95/EC "Low Voltage Directive" and 2009/125/EC "ErP Directive". The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings. [. . . ] Don't connect the RS-232C cable and the USB cable to the computer at the same time. [Example of Connection] Power Cable (Accessory) USB Cable (Accessory) RS-232C Cable (Accessory) Audio Cable (Accessory) D-Sub Signal Cable (Accessory) DVI-D Signal Cable (Accessory) Computer [Collect Cables] Put the cables through the cable holder and holes. Collect cables at the back of the stand. Cable Holder Cable Holes BEFORE YOU OPERATE THE MONITOR 7 ENGLISH COMPUTER SETTING Signal Timing Change to the desired signal timing listed on page 28: COMPLIANT TIMING. Windows 95/98/2000/Me/XP/Vista/7 Plug & Play The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows 95/98/2000/Me/XP/Vista/7 by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied. For installation on Windows 95/98/2000/Me/XP: The monitor Information File for iiyama monitors ENGLISH may be necessary for your computer and obtained via the Internet, using the address: http://www. iiyama. com NOTE For additional information on how to download the driver for your touch screen monitor, please access the internet site noted above. Monitor Drivers are not required in most cases for Macintosh or Unix operating systems. For further information, please contact your computer dealer first for advice. Procedure for turning ON the Power Switch Turn ON the monitor first, and then the computer. Touch screen driver software Touch screen driver software and system may not start when you start your computer while touching the screen. Touch screen driver software may not run due to the power saving function depending on the BIOS of your computer. In this case, set the power saving function to off. ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor. Hold the panel so that the monitor does not topple when you change the monitor's angle. You are able to adjust the monitor 's angle up to 90 degrees upward, 5 degrees downward. NOTE Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Careful attention is required not to catch your fingers or hands when you change the angle. 90° 5° 8 BEFORE YOU OPERATE THE MONITOR OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 28. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 14 for SCREEN ADJUSTMENTS. Press the Button to start the On Screen Display feature. There are additional Menu items which can be switched by using the / Buttons. C ON TR A ST B R IGH TN ESS 1280x1024 FH: 63KHz FV: 59. 9Hz B Select the Menu item which contains the adjustment icon relating to the adjustment you want to make. Use the Buttons to highlight the desired adjustment icon. C Use the / Buttons to make the appropriate adjustment or setting. D Press the Button to leave the menu, and the settings you just made would be automatically saved. For example, to correct for vertical position, select Menu item of . [. . . ] Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists. If you are experiencing a problem which is not described below or you cannot correct the problem, discontinue using the monitor and contact your dealer or iiyama service center for further assistance. Check The Power Cable is firmly seated in the socket. Please check with another piece of equipment. [. . . ]