User manual IMG STAGE LINE MPX-808

[. . . ] ASSIGN B for the crossfader (13); to select the input channel faded in when the crossfader is moved to the right 15 Button TALK OVER for microphone announcements: With the button pressed, the levels of the channels CH 1 ­ 4 and MIC 1 ­ 4 will be attenuated by 14 dB when announcements are made via the DJ microphone. 16 Level control for the DJ microphone 17 Level controls each for the master channels A and B 18 Rotary switch MONITOR for selecting a stereo input channel CH 1 ­ 4 or a master channel The signal of the channel selected will be indicated by the VU-meter (6) and can be monitored via headphones (prefader monitoring for the input channels, post-fader monitoring for the master channels). 1 Equalizers for the stereo channels CH 1 ­ 4: HIGH (±12 dB/10 kHz) MID (±12 dB/1 kHz) LOW (±12 dB/100 Hz) 2 Input selector switches of the stereo channels CH 1 ­ 4: Button not pressed Selection of the unit at the corresponding jack LINE (29). The two lower LEDs "ON" serve as a power indication. [. . . ] Second mixer) to the corresponding output jacks: ­ The master signal of the master channel A is available at the XLR outputs LEFT and RIGHT (24) and at the phono outputs MASTER A (25). The balanced signal transmission offers a higher protection against interference which may particularly occur with long connection cables. ­ The master signal of the master channel B is available at the phono output MASTER B (26). 2) For audio recordings , connect a recorder to the output REC (27). The recording level is independent of the position of the two master faders A and B (17). 3) Via stereo headphones, it is possible to monitor the signal of the stereo input channels CH 1 ­ 4 respectively ahead of the channel faders or to monitor the current music programme of the The mixer MPX-808 with four stereo input channels, four microphone channels, and a DJ microphone channel is suitable for various private or professional DJ applications. The mixer can either be placed as desired or be installed into a console. Prior to connecting any units or to changing any existing connections, switch off the mixer and all other audio units or set all output signals to zero. The light GNL-205 from "img Stage Line", to the BNC jack LAMP (8). The light is switched on and off with the mixer. 2) Select the signal sources connected to the channels CH 1 ­ 4 with the input selector switches LINE/PHONO (2): Button not pressed Selection of the unit at the corresponding jack LINE (29). button pressed (LED lights up) Selection of the turntable at the corresponding jack PHONO (30). 3) Feed an audio signal (test signal or music piece) to the first input channel used and set the corresponding channel fader (12) to approx. 4) Advance the corresponding master fader A or B (17) to such an extent that the signal is reproduced in an optimum way for the following adjustments via the audio system connected. For this purpose, slide the crossfader (13) to the left stop or to the right stop, if required. (The signal can also be checked via headphones ­ see chapter 5. The VU-meter (6) will indicate the level of the input channel ahead of the channel fader. 6) Via the VU-meter, control the level of the channel with the corresponding GAIN control (3). With an optimum level control, the 0 dB range of the VU-meter will light up with music peaks. Therefore, after readjusting the sound, always check the channel level by means of the VU-meter and readjust it, if required. 8) Repeat the adjustments of level and sound for the other stereo input channels used as described above. 1) For an optimum level adjustment of the microphone channels, first set their GAIN controls (7) and their equalizer controls (10) to mid-position. [. . . ] Each of the stereo input channels CH 1 ­ 4 can be monitored via headphones connected to the jack (19), even if the corresponding channel fader (12) is set to minimum. Alternatively, it is also possible to monitor the current music programme of the master channel A or B. Speak into the microphone connected to the jack DJ MIC (4) and adjust the desired volume with the control LEVEL (16) and the sound with the controls (5) HIGH, MID, and LOW. To automatically reduce the volume of all other signals by 14 dB while speaking in order to improve the intelligibility of an announcement, press the button TALK OVER (15) beforehand. [. . . ]