User manual INDESIT D 41

[. . . ] Dishwasher Instruction for installation and use D 41 Safety Is a Good Habit to Get Into NOTICE Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of the appliance. This appliance complies with the following EEC directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. 1. Carefully dispose of the packing material. 2. After removing the packing, check to make sure that the appliance is not damaged. [. . . ] At this point, the appliance is on and ready to be programmed. Turn the cycle selector knob "D" until the reference notch on the knob corresponds with the number or the symbol for the cycle you wish to set (have a look at the wash cycle table on page 7). After a few seconds, you will hear a short beep and the indicator light "G" comes on, indicating that the wash cycle has begun and it is not advisable to make any changes at this point. Cycle phase indicator lights The dishwasher is provided with 4 indicator lights "G" which come on in sequence as the appliance is performing that specific phase of the wash cycle. These phases are, from left to right: If you forget to load some of the dishes. . . The wash cycle can be interrupted by pressing the ON-OFF. You can then load additional dishes and turn the appliance back on. The end of the wash cycle is signalled by 2 short beeps and a flashing drying phase indicator light "G". Set the knob to the Reset position to clear all settings. Turn the appliance off by pressing button "A", thus cutting off the electricity supply. Wait a few minutes before unloading the dishes: they are very hot!If you wait a little while, they dry better thanks to the steam. Make sure the wash cycle has ended before removing the dishes!The wash cycle stops and then restarts when the electricity comes back on or when you close the door. pre-wash, wash, rinses, drying Cancelling or modifying a wash cycle in progress. . . . . Premise: You can cancel the wash cycle in progress, if it has only just started. To modify a wash cycle in progress, turn the knob anticlockwise and set it to Reset, after a few seconds you will hear 4 beeps and indicator light "G" will go out: this means all the settings have been cancelled. You are now free to reset the correct wash cycle. Warning If opening the door soon after the end of the programme, or during it, stand away from the Dishwasher, to avoid possible injury from hot steam. GB 6 Wash Cycle Table Cycle Cycle selection instructions Cycle description Detergent for prewash + wash Rinse Aid 1) Heavy Duty Very dirty dishes and pans (not to be used for delicate items). Pre-wash with cold water Pre-wash with hot water at 45°C Extended wash at 70°C. Cold rinse Rinse with hot water at 70°C. Drying. 5+15 gr. * 2) Normal wash Normally dirty pans and dishes. Standard daily cycle. 2 pre-washes with cold water. Drying. 5+15 gr. * 3) Rapid 25' Economic and fast cycle to be used for slightly dirty dishes. Cold rinse. 15 gr. 4) Soak Preliminary wash cycle for dishes and pans awaiting completion of the load with the dishes from the next meal. Short cold wash to prevent food from drying onto the dishes. 7 GB Energy Saving Tips - It is important to try and run the dishwasher when it is fully loaded in order to save on energy. [. . . ] The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line. Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter of 4 cm. , or let it run into the sink, making sure to avoid bending or crimping it. Use the speical plastic support that comes with the appliance (see figure to the right). The free end of the hose must be at a height between 40 and 100 cm. and must not be immersed in water. [. . . ]