User manual INDESIT D66S

[. . . ] Dishwasher Instruction for installation and use D 66 Safety Is a Good Habit to Get Into NOTICE Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of the appliance. This appliance complies with the following EEC directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. 1. Carefully dispose of the packing material. 2. After removing the packing, check to make sure that the appliance is not damaged. [. . . ] Make sure that the water supply is turned on to full pressure. Load the dishwasher (see the section entitled, "Loading the Dishwasher"). Pour in the detergent (see the section entitled, "Salt, Detergent and Rinse Aid"). Turn the knob located on the right of the control panel in the clockwise direction until the number or symbol for the cycle setting is aligned with the reference mark (see the section entitled, "Wash Cycle Table"). Press the ON-OFF botton, and the ON-OFF light will turn on. At this point, the wash cycle will begin. Cancelling or modifying a wash cycle setting. . . Premise: A cycle that is underway can only be modified if it has only been running for a short time. If you forget to load some of the dishes. . . The wash cycle can be interrupted by pressing the ON-OFF button. You can then load additional dishes and turn the appliance back on. When the knob stops turning and is aligned with a STOP mark (see figure), the cycle has finished. Turn off the appliance using the ON-OFF button, turn off the water STOP supply and open the door of the dishwasher. Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. Warning: If opening the door soon after the end of the programme, or during it, stand away from the Dishwasher, to avoid possible injury from hot steam. Press the ON-OFF button, and the ON light will turn off. Rotate the knob in the clockwise direction to the desired cycle setting (see the section entitled, "Starting a wash cycle. . . "). Then, turn the dishwasher back on using the ON-OFF button. Wash Cycle Adjustment Buttons "Intensive 65°C" Button This button (see "Close-up View - Control Panel", letter "E") is used with the normal cycle in the case where pots and pans with dry caked-on food must be washed. This is not recommended for delicate items in so far as the high temperatures could make their surfaces opaque or lighten decorative colors after repeated washing. "Half Load "Button" This button (see "Close-up View - Control Panel", letter "F") makes it possible to wash dishes using only the upper rack if there are not enough dishes for a full load. This will allow you to save on water and electrical energy. It can be used before setting any of the wash cycles, except for the intensive cycles (if included in the wash cycle table). Please keep in mind that the amount of detergent should also be cut in half. GB 6 Wash Cycle Table Cycle INTENSIVE 65°C Button Cycle Selection Information Description of Cycle Detergent for Pre-wash + Wash Rinse Aid 1) Normal Wash 55°C Normally dirty dishes, pots and pans. Standard daily cycle. 2 pre-washes with cold water. Drying. 5+25 gr. * 1) Normal Wash Very dirty dishes, pots and pans (not to be used with delicate items). Pre-wash with cold water. [. . . ] In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced. The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line. Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter of 4 cm. , or let it run into the sink, making sure to avoid bending or crimping it. Use the speical plastic support that comes with the appliance (see figure to the right). [. . . ]