User manual INDESIT DIF1614

[. . . ] This appliance is intended to be used in household and similar applications such as: - staff kitchen areas in shops, offices and other working environments; - farm houses; - by clients in hotels, motels and other residential type environments; - bed and breakfast type environments. Connecting the water inlet hose • To a suitable cold water connection point: before attaching the hose, run the water until it is perfectly clear so that any impurities that may be present in the water do not clog the appliance; after performing this operation, screw the inlet hose tightly onto a tap with a ¾ gas threaded connection. • To a suitable hot water connection point: your dishwasher may be supplied with hot water from the mains supply (if you have a central heating system with radiators) provided that it does not exceed a temperature of 60°C. Screw the hose to the tap as described for connection to a cold water supply. If the inlet hose is not long enough, contact a specialist store or an authorised technician (see After Sales Service). [. . . ] Do not use table salt or industrial salt, or washing up liquid. Follow the instructions given on the packaging. If using a multi-functional product it is not necessary to add rinse aid; however, we recommend that you add salt, especially if you live in an area where the water is hard or very hard. Follow the instructions given on the packaging. Hardness level 2 (1st cycle indicator light ON, 2nd cycle indicator light flashing) Hardness level 3 (1st and 2nd cycle indicator lights ON, 3rd cycle indicator light flashing etc) up to maximum 5 levels. - Press the P button repeatedly until the desired hardness level has been reached (1-2-3-4-5* see Water hardness table). - To exit the function, wait approximately few seconds or press another option* button, or switch off the machine using the ON/ OFF button. Even if using multi-functional tablets, the salt dispenser should still be filled. Water Hardness Table Level 1 2 3 4 °dH 0-6 6 - 11 12 - 17 17 - 34 °fH 0 - 10 11 - 20 21 - 30 31 - 60 mmol/l 0-1 1, 1 - 2 2, 1 - 3 3, 1 - 6 Average salt container capacity duration** months 7 months 5 months 3 months 2 months EN If you do not add salt or rinse aid, the LOW SALT* and LOW RINSE AID* indicator lights remain lit. Rinse aid makes it easier for the crockery to dry, as water runs off surfaces more readily and therefore does not leave streaks or marks. The rinse aid dispenser should be filled: • When the LOW RINSE AID* indicator light on the control panel is illuminated; 1. Open the dispenser by turning the lid (G) in an anticlockwise direction. Pour in the rinse aid, making sure it does not overflow from the F dispenser. If this happens, clean the spill immediately with a dry G cloth. - Unscrew the end of the water inlet hose, remove the filter and clean it carefully under running water. - Replace the filter and screw the water hose back into position. Cleaning the dishwasher Cleaning the filters The filter assembly consists of three filters which remove food residues from the washing water and then recirculate the water. They should be cleaned if you wish to achieve the best results in every wash. The dishwasher should not be used without filters, or if the filter is loose. • After several washes, check the filter assembly and if necessary clean it thoroughly under running water, using a non-metallic brush and following the instructions below: 1. Turn the cylindrical filter C in an anti-clockwise direction and pull it out (fig. Remove the cup filter B by exerting a slight pressure on the side flaps (fig. Slide out the stainless steel plate filter A (fig. Inspect the trap and remove any food residue. NEVER REMOVE the wash cycle pump (black detail) (fig. 4). • Always keep the door of the appliance ajar in order to avoid moisture from forming and being trapped inside the machine. [. . . ] • • • • • The dishes and glasses are covered in a white film or limescale deposits. The dishes and glasses are streaked or have a bluish tinge. The crockery has not been dried properly. The dishes are not clean. • • • (several short beeps* are emitted) (the 2 (Normal) and 3 (Soak) WASH • CYCLES indicator lights flash). The dishwasher does not take any water in - Tap shut-off alarm Water inlet hose alarm / Water inlet • Switch off the appliance by pressing the ON/OFF button. [. . . ]