User manual INDESIT IPG 751 S BK

[. . . ] Com 11 Operating Instructions HOB Contents Installation, 13-16 IT Italiano, 1 GB G B English, 12 FR Français, 22 NL Nederlands, 34 ES Español, 46 PT Português, 57 Positioning Electrical connection Gas connection Data plate Burner and nozzle specifications Description of the appliance, 17 Overall view BE Deutsch, 68 Start-up and use, 18 Practical advice on using the burners Precautions and tips, 19 General safety Disposal IPG 640 S IPG 751 S Maintenance and care, 20 Switching the appliance off Cleaning the appliance Gas tap maintenance Troubleshooting, 21 Installation !Before operating your new appliance please read this instruction booklet carefully. It contains important information for safe use, installation and care of the appliance. Please keep these operating instructions for future reference. [. . . ] Unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of gas (see table 1 “Burner and nozzle characteristics”). In the case of the Mini WOK burner, use a spanner with a 7 mm opening to unscrew the nozzle (see figure). Reassemble the parts following the above procedure in the reverse order. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Sticker are available from any of our Service Centres. € Adjusting the burners’ primary air : Does not require adjusting. • Setting the burners to minimum: 1. Remove the knob and adjust the adjustment screw, which is positioned in or next to the tap pin, until the flame is small but steady. Having adjusted the flame to the required low setting, while the burner is alight, quickly change the position of the knob from minimum to maximum and vice versa several times, checking that the flame does not go out. Some appliances have a safety device (thermocouple) fitted. If the device fails to work when the burners are set to the low flame setting, increase this low flame setting using the adjusting screw. Once the adjustment has been made, replace the seals on the by-passes using sealing wax or a similar substance. If the appliance is connected to liquid gas, the regulation screw must be fastened as tightly as possible. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Stickers are available from any of our Service Centres. Should the gas pressure used be different (or vary slightly) from the recommended pressure, a suitable pressure regulator must be fitted to the inlet pipe (in order to comply with current national regulations). DATA PLATE Electrical see data plate connections This appliance conforms to the following European Economic Community directives: - 2006/95/EEC dated 12/12/06 (Low Voltage) and subsequent amendments - 2004/108/EEC dated 15/12/04 (Electromagnetic Compatibility) and subsequent amendments - 93/68/EEC dated 22/07/93 and subsequent amendments. 78 MJ/m3 (1) Only for appliances with the security device. S R S A IPG 640 S RR MW A S S IPG 751 S 16 Description of the appliance Overall view GB GAS BURNERS Support Grid for COOKWARE Control Knobs for GAS BURNERS GAS BURNERS Support Grid for COOKWARE Control Knobs for GAS BURNERS SAFETY DEVICES * Ignition for GAS BURNERS * • GAS BURNERS differ in size and power. Use the diameter of the cookware to choose the most appropriate burner to cook with. € Control Knobs for GAS BURNERS adjust the size of the flame. • GAS BURNER ignition* enables a specific burner to be lit automatically. [. . . ] Clean the cooking surface when it is still warm with a suitable cleaning product (such as the one in the Solutions product line available from any After-Sales Service Centre) and paper towels. Aluminum foil, plastic items, objects made of synthetic material, Gas tap maintenance Over time, the taps may become jammed or difficult to turn. If this happens, the tap must be replaced. This procedure must be performed by a qualified technician authorised by the manufacturer. [. . . ]