User manual INDESIT ISL60V

[. . . ] Instruction booklet TUMBLE DRYER GB English, 1 Contents Installation, 2-3 Where to put your dryer Ventilation Electrical connection Before you start using your dryer GB Dryer description, 4 The front The back Control panel Start and programmes, 5-7 Choosing a programme Table of programmes The controls ISL60V Laundry, 8-9 Sorting your laundry Wash care labels Special clothing items Drying times Warnings and Suggestions, 10 General safety Disposal Saving energy and respecting the environment Maintenance and Care, 11 Switching off the electricity Cleaning the filter after each cycle Check the drum after each cycle Cleaning the dryer Troubleshooting, 12 Service, 13 Spare parts 1 Installation GB !Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and, should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the dryer so that the new owner may be informed about warnings and suggestions on how the dryer works. Read these instructions carefully; the following pages contain important information on installation and suggestions on how the appliance works. [. . . ] Position the PROGRAMME knob on the desired time: 120, 90, 60 or 30. Press the START button . Options available: Alarm Options available: Alarm , High Heat Delayed Start . , Consult suggested drying times (see Laundry). The last 10 minutes of these programmes is the Cool Tumble (see below). 1. Options available: Cool Tumble Brief programme (approximately 10 minutes) that cools fibres or clothing. Alarm 6 The Controls PROGRAMMES knob q GB High Heat When available this button selects high heat. Press this button and a high heat setting is selected and the light above the button comes on. Timed programmes have a default of low heat, if the light alongside the button is on then pressing the button selects a low heat setting and the light goes out. Alarm Available on all programmes and allows the buzzer to give a signal at the end of the drying cycle, to remind you that the clothes are ready to be removed. Press the button and the light will show that the option is selected. Post Creasecare The clothes are occasionally tumbled after the end of the drying and cool tumble cycles, to help prevent creases developing should you not be available to remove the load immediately the programme is complete. !Warning, if after pressing the start button, the programmes knob position is changed, the new position will NOT change the programme selected. Position 0, turning the knob to position 0 resets and cancels a programme. Installation q OPTION buttons / lights Description These buttons are used to customise the selected programme to your requirements. A programme must have been selected on the programme knob before an option can be selected. Not all options are available for all programmes (see Start and Programmes). If an option is not available and you press the button, the buzzer will beep four times. If the option is available there will be one beep and the option light above the button lights to confirm the selection. After the start button has been pressed only the Alarm option can be changed. Progress (Drying, Cool Tumble, Post Creasecare) / Delay (3hr 6hr 9hr 12hr) Lights When the light above the delay button is on, these lights flash to indicate the delay time is selected. During other programmes they indicate the progress of the dryer, each one comes on as the corresponding phase starts. Time Delay The start of some programmes (see Start and Programmes) can be delayed for up to 12 hours in 3hr steps. When a delayed start is in progress the light above the delay button will be on and the selected delay period light will flash (after the start button has been pressed). To set a delayed start, press the Time Delay button, and the light above the button will come on together with the 3hr delay light. Pressing the button again will advance the delay setting to 6hr, the 3hr light goes out and the 6hr light is on. [. . . ] Your dryer uses special bearing components which do not need lubrication. Have your dryer checked regularly by authorised technicians to ensure electrical and mechanical safety (see Service). Laundry Warnings and Suggestions Removing the filter: 1. Pull the plastic grip of the filter upwards (see diagram). Clean the filter and replace it correctly. [. . . ]