User manual INDESIT P 640

[. . . ] It is also a good idea to clean up any spills. Greasing the Gas Valves Over time, the gas valves may stick or become difficult to turn. If this is the case, the must be cleaned on the inside and the regreased. N. B. : This procedure must be performed by a technician authorized by the manufacturer. Practical Advice Practical Advise on Using the Burners For best performance, follow these general guidelines: · Use the appropriate cookware for each burner (see table) in order to prevent the flame from reaching the sides of the pot or pan; · Alwasy use cookware with a flat bottom and keep the lid on; · When the contents come to a boil, turn the knob to "Low". Burner Fast (R) Semi Fast (S) Auxiliary (A) ø Cookware diameter (cm) 24 - 26 16 - 20 10 - 14 Is there a problem? It may occur that the cooktop does not function or does not function properly. Before calling customer service for assistance, lets see what can be done. [. . . ] Check to make sure that: · The gas holes are not clogged. · There are no draughts near the cooking surface. · The minimum has been adjusted correctly (see the section entitled, "Minimum Regulation"). Check to make sure that: · The bottom of the cookware is perfectly flat. · The cookware is centered correctly on the burner . · The support grids have not been inverted. If, despite all of these checks, the cooktop does not function properly and problem persists, call the nearest Merloni Elettrodomestici Customer Service Centre, informing them of: - The type of problem. - The abbreviation used to identify the model (Mod. Never call upon technicians not authorized by the manufacturer, and refuse to accept spare parts that are not original. 4 Safety Is a Good Habit to Get Into To maintain the EFFICIENCY and SAFETY of this appliance, we recommend: · use only the MANUFACTURER Service · use only ORIGINAL Spare Parts · · This manual is for a class 3 built-in cooktop. This appliance is designed for non-professional use in the home and its features and technical characteristics must not be modified. These instructions are only valid for the countries the symbols for which appear on the manual and the serial plate. To obtain a good fixing of the hob plate it is advisable to use all the hooks supplied. 555 mm. mm 20 55 m m . . 475 Clamp Position for H=30mm top Front 40 30 Fastening Clamps - Assembly Diagram Clamp Position for H=20mm top HOOD min. 420 mm. Clamp Position for H=40mm top Back N. B: Use the clamps contained in the "accessory kit. " e) In the event the cooktop is not installed above a builtin oven, a wood panel must be inserted as insulation. This panel must be placed at least 20 mm from the bottom of the cooktop itself. Important: When installing the cooktop above a built-in oven, the oven should be placed on two wooden strips; in the case of a joining cabinet surface, remember to leave a space of at least 45 x 560 mm at the back. LESS THAN 420 6 that the flexible metal tube does not touch any moving parts and is not crushed. . mm 45 m 560 m. Check the Seal Once the appliance has been installed, make sure all the connections are properly sealed, using a soapy water solution. Electrical Connection The cooktops fitted with a tripolar electrical supply cord are designed to be be used with alternating current according to the indications on the rating plate located under the cooktop. The earthing wire can be identified by its yellow-green colour. In the case of installation over a built-in electric oven, the electrical connections for the cooktop and oven should be independent, not only for safety purposes, but also to facilitate removal of one or both in the future. Electrical Connection for Gas Cooktop Fit the supply cord with a standard plug for the demand rate indicated on the rating plate or connect it directly to the electrical mains. In the latter case, a single pole switch must be placed between the appliance and the mains, with a minimum opening between the contacts of 3 mm in compliance with current safety codes (the earthing wire must not be interrupted by the switch). [. . . ] Adapting the Cooktop for Different Types of Gas To adapt the cooktop to a different type of gas than that for which it was designed, (see the sticker under the hob or on the packaging), the burner nozzles must be changed, as follows: · Remove the pan supports and slide the burners out of the cooktop. · Unscrew the nozzles using a 7mm socket wrench and replace them with those for the new type of gas. (See table 1, "Burner and Nozzle Specifications"). 7 When installing the cooktop above a built-in oven without forced ventilation, ensure that there are air inlets and outlets for ventilating the interior of the cabinet adequately. Gas Connection for Cooktop The cooktop should be connected to the gas supply by an authorized installer. [. . . ]