User manual INDESIT P750AST

[. . . ] ), interrupting the delivery of gas to the burner. Indicator Light for Electric Hot Plate (only on certain models) How To Use Your Appliance The position of the corresponding gas burner or electric hot plate (if present) is indicated on each control knob. gas Burners The burners differ in size and power. Choose the most appropriate one for the diameter of the cookware being used. [. . . ] If, despite all of these checks, the cooktop does not function properly and problem persists, call the nearest Merloni Elettrodomestici Customer Service Centre, informing them of: - The type of problem. - The abbreviation used to identify the model (Mod. Never call upon technicians not authorized by the manufacturer, and refuse to accept spare parts that are not original. Safety Is a Good Habit to Get Into To maintain the EFFICIENCY and SAFETY of this appliance, we recommend: • call only the Service Centers authorized by the manufacturer • always use original Spare Parts • • • • This manual is for a class 3 built-in cooktop. This appliance is designed for non-professional use in the home and its features and technical characteristics must not be modified. These instructions are only valid for the countries the symbols for which appear on the manual and the serial plate. The electrical system of this appliance is safe only when it is correctly connected to an adequate earthing system, as required by current safety standards. - Prevent children and the disabled from coming into contact or having access to the following, as they are possible sources of danger: - The controls and the appliance in general; - The packaging (plastic bags, polystyrene, nails, etc. ); - The appliance, during and immediately after use given the heat generated by its use; - The appliance when no longer in installed (in this case, all potentially dangerous parts must be made safe). The following should be avoided: - Touching the appliance with wet parts of the body; - Using the appliance with bare feet; - Pulling on the appliance or the power supply cord to disconnect them from the electrical outlet; - Improper and/or dangerous use; - Obstructing the ventilation or heat dissipation slots; - Allowing the power supply cord of small appliances to 13 come into contact with the hot parts of the cooktop; Exposure to atmospheric agents (rain, sun); Using flammable liquids nearby; Using adaptors, multiple outlet plugs and/or extensions; Using unstable or deformed cookware; Leaving the electric hobs on without cookware on top of them; Closing the glass top (if present) while the gas burners or electrical hot plates are still hot; Trying to install or repair the appliance without the assistance of qualified personnel. The assistance of qualified personnel must be called upon in the following cases: - Installation (in accordance with the manufacturer's instructions); - When in doubt about the operation of the appliance; - Replacement of the electrical outlet becuase it is incompatible with the plug. (exclusively for cooking appliances) Directly to the Outside b) The room must also allow for the influx of the air needed for proper combustion. The flow of air for combustion purposes must not be less than 2 m³/h per kW of installed capacity. The supply of said air can be effected by means of direct influx from the outside through a duct with a inner cross section of at least 100 cm² which must not be able to be accidentally blocked. If not, follow the instructions indicated in the section entitled, “Adapting the Cooktop for Different Types of Gas”. If the cooktop is to be connected to tanks containing liquid gas, use pressure regulators that comply with current safety standards. Important: To insure that the appliance operates safety, the gas is regulated correctly and your appliance lasts over time, make sure that gas pressure levels comply with the indications given in Table 1, “Nozzle and Burner Specifications”. Gas Connection to Non-flexible Pipe (copper or steel) Connection to the gas source must be done in such a way as to not create any stress points at any part of the appliance. The appliance is fitted with an adjustable, "L" shaped connector and a gasket for the attachment to the gas supply. Should this connector have to be turned, the gasket must be replaced (supplied with the appliance). The gas feed connector to the appliance is a threaded, male 1/ 2" connector for round gas pipe. Clamp Position for H=40mm top Back 15 Gas Connection to Flexible Steel Pipe The gas feed connector to the appliance is a threaded, male 1/ 2" connector for round gas pipe. [. . . ] If the gas pressure is different than that prescribed, a pressure regulator must be installed at the source, in compliance with national standards governing the use of piped gas regulators. Regulation of Air Supply to the Burner The burners do not need a primary air regulator. minimum Regulation • Turn the gas valve to minimum. € Remove the knob and turn the regulator screw (positioned either on the side of the top or inside the shaft) clockwise until the flame becomes small but regular. [. . . ]