User manual INDESIT PI604

[. . . ] To fasten the cooktop securely, it is recommended that all the clamps be used. clamp Position for H=40mm top 40 Back !Use the clamps contained in the "accessory kit. " • In case a wooden panel should be fitted under the top for insulation, it will have be fitted at a minimum distance of 20 mm from the inferior part of the top. [. . . ] 555 mm mm 55 m m When installing on a built-in oven without forced ventilation, ensure that there are air inlets and outlets for ventilating the interior of the cabinet adequately (see picture). 2 475 30 Supply cable installation The electrcic hobs are supplied without cable. 5mm2 • Open the terminal box by removing the "V" screw and taking off the cover. GB Electrical connection The following installation procedure must be carried out by a qualified electrician. The cooker must be connected to the mains by a switched (double pole) cooker outlet correctly fused with a capacity appropriate to that shown on the hob Rating Plate. All electrical wiring from the consumer unit to the appliance, via the switched double pole cooker outlet, must be of an acceptable type and current rating as above. 5mm2, must be positioned so that it never reaches at any point a temperature 50°C higher than the room temperature. The electrical installation must comply with the IEE Regulations, Building Regulation & local By-Lays. In the case of installation over a built-in electric oven the electrical hook-up of the stove top and that of the oven should be separate, for reasons of safety as well as for ease of eventual removal of the oven. • The wires in the mains lead are coloured in accordance with the following code: Green & Yellow - Earth “E” Blue - Neutral “N” Brown - Live “L” Connect the wires in accordance with the following diagram 1 2 L 3 4 N 5 • Fix the cable in place with the "F" cable clamp, close the lid and fasten it with the "V" screw (see picture). V 1 2 3 4 5 F 3 Description of the appliance GB Overall view ELECTRIC PLATE Pilot lamp of the ELECTRIC PLATE Control knobs for the cook-top ELECTRIC PLATE • The ELECTRIC PLATE vary in diameter and power: "normal" and "fast". • In the case of a malfunction, under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or further malfunctioning of the appliance. contact a Service Centre (see Assistance). • Always make sure pan handles are turned towards the centre of the hob in order to avoid accidental burns. Disposal • When disposing of packaging material: observe local legislation so that the packaging may be reused. • The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance. Practical Advice on Using the Electric Hot Plates In order to avoid heat loss and damage to the hot plate, use cookware with a flat bottom the diameter of which is not less than that of the hot plate. setting 0 1 2 3 4 5 6 Normal or Fast Plate Off Cooking vegetables , fish Cooking potatoes (using steam) soups , chickpeas , beans. [. . . ] setting 0 1 2 3 4 5 6 Normal or Fast Plate Off Cooking vegetables , fish Cooking potatoes (using steam) soups , chickpeas , beans. Continuing the cooking of large quantities of food, minestrone For roasting (average) For roasting (above average) For browning and reaching a boil in a short time. Before using the hot plates for the first time, you should heat them at maximum temperature for approximately 4 minutes, without any pans. During this initial stage, their protective coating hardens and reaches its maximum resistance. [. . . ]