User manual INDESIT PI640A

[. . . ] The minimum distance combustible material kitchen units can be fitted directly above the hob is 700mm. HOOD min. 50 • The hob should not be installed in a bed sitting room with a volume of less than 20m3. If it is installed in a room of volume less than 5m3 an air vent of effective area of 110cm2 is required, if it is installed in a room of volume between 5m3 and 10m3 an air vent of effective airvent of 50cm2 is required, while if the volume exceeds 11m3 no airvent is required. However, if the room has a door or a window which opens directly to the outside no air vent is required even with the volume is between 5m3 and 11m3. [. . . ] Use the clamps contained in the "accessory kit. " • In the event the cooktop is not installed above a built-in oven, a wood panel must be inserted as insulation. This panel must be placed at least 20 mm from the bottom of the cooktop itself. Ventilation When installing the cooktop above a built-in oven, the oven should be placed on two wooden strips; in the case of a joining cabinet surface, remember to leave a space of at least 45 x 560 mm at the back (see picture). 5 m 60 m . 45 m m. !The hob can only be installed above built-in ovens provided with cooling ventilation. Electrical connection The cooktops fitted with a tripolar electrical supply cord are designed to be be used with alternating current according to the indications on the rating plate located under the cooktop. The earthing wire can be identified by its yellow-green colour. In the case of installation over a built-in electric oven, the electrical connections for the cooktop and oven should be independent, not only for safety purposes, but also to facilitate removal of one or both in the future. 3 GB Gas Connection The cooktop should be connected to the gas supply by an authorized installer. During installation of this product it is essential to fit an approved gas tap to isolate the supply from the appliance for the convenience of any subsequent removal or servicing. Connection of the appliance to the gas mains or liquid gas tanks must be carried out according to the safety standards currently in force, and only after it is ascertained that it is suitable for the type of gas to be used. If not, follow the instructions indicated in the section entitled, “Adapting the Cooktop for Different Types of Gas”. If the cooktop is to be connected to tanks containing liquid gas, use pressure regulators that comply with current safety standards. To insure that the appliance operates safety, the gas is regulated correctly and your appliance lasts over time, make sure that gas pressure levels comply with the indications given in Table 1, “Nozzle and Burner Specifications”. If the gas pressure is different than that prescribed, a pressure regulator must be installed at the source, in compliance with national standards governing the use of piped gas regulators. DATA PLATE Class: II2H3+ Rated power kW (1): 8, 05 (585 g/h - G30) (575 g/h - G31) voltage: 220-240V ~ 50/60Hz GB Gas section Electrical section This appliance conforms to the following European Economic Community directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent amendments; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent amendments; - 90/396/EEC of 29/06/90 (Gas) and subsequent modifications; - 93/68/EEC of 22/07/93 and subsequent amendments. (1): The values in g/h refer to the capacities with liquid gas (Butane, Propane). 5 GB Characteristic of the burners and nozzles Table 1 Burner Diameter (mm) Thermal power kW (p. c. s. *) Nomin. Fast (R) Semi Fast (S) Auxiliary (A) Triple Crown (TC) Supply Pressures ** ** *** Liquid Gas By-Pass 1/100 (mm) 41 30 30 57 Nozzle 1/100 (mm) 87 70 52 91 *** 218 138 73 236 28-30 20 35 Flow* g/h ** 214 136 71 232 37 25 45 Natural Gas Nozzle 1/100 (mm) 128 104 76 133 20 17 25 286 181 95 309 Flow* l/h Ridot. 0, 70 0, 40 0, 40 1, 30 100 75 51 130 3, 00 1, 90 1, 00 3, 25 Nominal (mbar) Minimum (mbar) Maximum (mbar) At 15°C and 1013 mbar-dry gas Propane P. C. S. = 37. 78 MJ/m3 S R S A S TC S A PI 640 A GB PI 640 TC GB 6 Description of the appliance Overall view Support Grid for Cookware Gas Burners GB Control Knobs for Gas Burners Ignition Button for Gas Burners Ignitor for Gas Burners 7 Start-up and use GB The position of the corresponding gas burner is indicated on each control knob. Gas Burners The burners differ in size and power. Choose the most appropriate one for the diameter of the cookware being used. The burner can be regulated with the corresonding control knob by using one of the following settings: • Off High Low To turn on one of the burners, place a lighted match or lighter near the burner, press the knob all the way in and turn in the counter-clockwise direction to the "High" setting. On those models fitted with an ignitor, the ignition button, identified by the symbol, must first be pressed and then the corresponding knob pushed all the way in and turned in the counter-clockwise direction to the "High" setting. If the burner accidently goes out, turn off the gas with the control knob and try to light it again after waiting at least 1 minute. To turn off a burner, turn the knob in the clockwise direction until it stops (it should be on the “•” setting). Practical Advise on Using the Burners For best performance, follow these general guidelines: • Use the appropriate cookware for each burner (see table) in order to prevent the flame from reaching the sides of the pot or pan; • Alwasy use cookware with a flat bottom and keep the lid on; • When the contents come to a boil, turn the knob to "Low". Burner Fast (R) Semi Fast (S) Auxiliary (A) Triple Crown (TC) ø Cookware Diameter (cm) 24 - 26 16 - 20 10 - 14 24 - 26 8 Precautions and tips ! [. . . ] Check to make sure that: • The gas holes on the burner are not clogged; • All of the movable parts that make up the burner are mounted correctly; • There are no draughts around the cooking surface. The flame does not stay lighted on the model with the safety device. Check to make sure that: • You press the knob all the way in; • You keep the knob pressed in long enough to activate the safety device. • The gas holes are not clogged in the area corresponding to the safety device. [. . . ]