User manual INDESIT WG1030G

[. . . ] Saves while it washes The double action wash penetrates so deeply that at just 60°C you obtain the same results you would normally obtain at 90°C with a traditional washer. Controlled consumption The machine automatically adjusts the amount of water used in the wash to the size of the load, giving optimum use of water, energy and detergent. Double-action wash Clothes are soaked in water and detergent, water then “rains” steadily through the clothes. Safety, a good habit to get into CAUTION Please read the instructions in this handbook carefully, as they contain important information about safe installation, operating and servicing. [. . . ] Load your laundry in the washer, add the detergent and fabric softener and remember to: - shut the door properly - plug the washer in at the mains - turn on the water supply - check that button C is not pressed in (position O) Anti-crease This feature interrupts the wash cycle, letting the laundry soak in the water before the spin cycle. It is activated only during the wash cycles for synthetic materials and wool. This feature is very useful because it prevents delicate and synthetic clothing from wrinkling (for example, when you are unable to remove the laundry at the end of the wash cycle and it must remain in the machine for several hours). The wash program can be completed with either a spin cycle or by draining the water without wringing. In the first case, simply turn the knob A clokwise one click. In the second, turn the knob A to the drain setting, n°15. In both cases, the knob A must be turned when the machine is off. Selecting the programme The table on pages 5 will help you choose the right programme. Turn dial A to the programme number you have chosen and, if necessary, press functions buttons D, E; set ON/OFF button C to position I (ON). To turn off the washer press the ON-OFF button C and wait approximately 3 minutes before opening the door. Once you have removed your clean laundry from the washer, remember to leave the door open or at least ajar (this will prevent the formation of an unpleasant odour) and shut off the water supply. Do not exceed the recommended weights shown in the table For best washing results, do not exceed the recommended weights shown in the table; the weights shown refer to dry laundry. Maximum dry laundry load heavy fabrics maximum 5 kg delicate fabrics maximum 2 kg pure new wool maximum 1 kg mixed loads maximum 2, 5 kg How heavy is your laundry?1 sheet 400-500 g 1 pillow case 150-200 g 1 table cloth 400-500 g 1 bathrobe 900-1200 g 1 bathroom towel150-250 g GB 6 Energy saving hints - Try to wash complete laundry loads: this saves unnecessary consumption of water and energy. - Select the right programme for your laundry: this will obviously depend on the type of fabric and how soiled your laundry is; we recommend the use of programmes without prewash which will save you time, water and energy. The prewash cycle should in fact be used only for heavily soiled, cotton fabrics. - Set the right temperature: use temperatures above 60°C only for very stubborn dirt but remember that modern detergents are very efficient even at low temperatures. - Use the correct quantities of detergent: do not use too much detergent; remember that not only will this make rinsing more difficult but also pollutes the enviroment. - Use the economy buttons: when washing small laundry loads use the Economy button if available on your washer and reduce the detergent quantity. - Your washer features automatic consumption control, this means that you can wash laundry loads from 1 - 5 kg with considerable savings. Your washer will use just the right amount of water and electricity. All you need to do is dose the detergent. [. . . ] If the washer is installed on a carpeted floor, check that there is sufficient ventilation space between the floor and the bottom of the washer. Water supply Both hot and cold water supplies are preferable and they should be between 34. The hose having the red end fitting should be encountered between the hot supply and the threaded connection adjacent to the letter H on the rear of the machine. The hose having the white end fittings should be connected between the cold supply and the threaded connection adjacent to the letter C on the rear of the machine (see fig. [. . . ]