User manual INDESIT WIE 137 S

[. . . ] Instructions for use WASHING MACHINE Contents GB English, 1 GB Installation, 2-3-4-5 Unpacking and levelling, 2 Electric and water connections, 2-3 The first wash cycle, 4 Technical details, 5 Washing machine description, 6-7 Control panel, 6 Display, 7 MEMO Programme, 7 Starting and Programmes, 8 Briefly: how to start a programme, 8 Programme table, 8 Personalisations, 9 WIE 137 S Setting the spin cycle, 9 Setting the Delay Timer, 9 Setting the temperature, 9 Functions, 9 Detergent dispenser, 10 Bleach cycle, 10 Preparing your laundry, 10 Special items, 10 Woolmark, 10 Detergents and laundry, 10 Precautions and advice, 11 General safety, 11 Disposal, 11 Saving energy and respecting the environment, 11 Care and maintenance, 12 Cutting off the water or electricity supply, 12 Cleaning your appliance, 12 Cleaning the detergent dispenser, 12 Caring for your appliance door and drum, 12 Cleaning the pump, 12 Checking the water inlet hose, 12 Troubleshooting, 13 Service, 14 Before calling for Assistance, 14 1 Installation GB Keep this instruction manual in a safe place for future reference. Should the appliance be sold, transferred or moved, make sure the instruction manual accompanies the washing machine to inform the new owner as to its operation and features. Read these instructions carefully: they contain vital information on installation, use and safety. Levelling your appliance correctly will provide it with stability and avoid any vibrations, noise and shifting during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the washing machine. Unpacking and levelling Unpacking Electric and water connections Connecting the water inlet hose 1. [. . . ] Press it again and the values lower until they reach OFF, which indicates that the spin cycle has been excluded (press it again to go back to the maximum value); stop on the desired speed, after approximately remains fixed. 2 seconds the setting is accepted: the symbol The spin cycle setting is enabled with all the programmes except for 6 and the Draining cycle. Setting the spin cycle GB Installation Press the button and you will see the word OFF on the display, while the relative symbol flashes. Press the button again and "1h" appears, that is, a delay of one hour (this can reach up to 24h); stop on the "desired" delay; after approximately 2 seconds the setting is accepted, following which, the time for the set programme appears on the display and the remains on. symbol If you now press the START/RESET button, the set "delay" appears; this decreases every hour until the start of the cycle. In this phase, the "delay" can only be modified by decreasing it. The Delay Timer regulation is enabled with all programmes. If, when the appliance is switched on, the KNOB is positioned on a programme for which the temperature needs to be regulated, a fixed appears. Press button and the maximum temperature allowed for the programme set will be displayed and the icon flashes. Press it again and the temperature lowers until it reaches OFF, which indicates a cold wash cycle (press it again to go back to the maximum value); stop on the desired value, after approximately 2 seconds the setting is accepted: the symbol remains fixed. The temperature adjustment is enabled with all wash programmes. Setting the Delay Timer Description Programmes Setting the temperature Detergents Functions To enable a function: 1. press the button corresponding to the desired function, according to the table below; 2. the function is enabled when the corresponding button is illuminated. Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the programme set. If you set a function that is incompatible with another function you selected previously, only the last one selected will be enabled. Function Effect Bleaching cycle designed to remove the toughest stains. This option reduces the amount of creasing on fabrics, making them easier to iron. Comments Please remember to pour the bleach into extra compartment 4 (see page 10). This function is incompatible with the EASY IRON function. Enabled with programmes: 2, 3, 4, 5, Rinse cycle. Precautions Care Stain removal Troubleshooting Recommended when the appliance has a full load or with large quantities of detergent. When this function is set, programmes 4 and 6 will end, with the laundry left to soak (Anti-crease), and the relative button flashes: - to conclude the cycle, press the START/RESET button or the EASY IRON button; - to run the draining cycle alone, set the knob to the relative symbol and press the START/RESET button. This function is incompatible with the STAIN REMOVAL function. Extra Rinse 1, 2, 3, 4, 7, 8, 9, 11, 12, Rinse cycle. Easy iron 3, 4, 6, 7, 8, 9, Rinse cycle. Service The machine has an intelligent built in check for out of balance loads. To let protect your machine it may reduce the final spin speed if an unbalanced load is detected. 9 Detergents and laundry GB Detergent dispenser Good washing results also depend on the correct dose of detergent: adding too much detergent won't necessarily make for a more efficient wash, and may in fact cause build up on the interior of your appliance and even pollute the environment. Open up the detergent dispenser and pour in the detergent and fabric softener, as follows. Preparing your laundry Divide your laundry according to: - the type of fabric/the symbol on the label. [. . . ] If you see any cracks, replace it immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open. Never use hoses that have already been used. 12 Troubleshooting Your washing machine could fail to work. Before calling for Assistance (see page 14), make sure the problem can't easily be solved by consulting the following list. GB Installation Problem The washing machine won't start. Possible causes/Solution: The appliance is not plugged into the socket, or not enough to make contact. The appliance door is not shut properly (the word DOOR is displayed). The The START/RESET button has not been pressed. [. . . ]