User manual INDESIT XWA 71252 WWB

[. . . ] 2 Raccordement du tuyau de vidange Raccorder le tuyau d’évacuation, sans le plier, à un conduit d’évacuation ou à une évacuation murale placés à une distance du sol comprise entre 65 et 100 cm ; ou bien l’accrocher à un évier ou à une baignoire, dans ce cas, fixer le support en plastique fourni avec l’appareil au robinet (voir figure). 12 Instructions for use WASHING MACHINE Contents Installation, 14-15 GB English Unpacking and levelling Connecting the electricity and water supplies The first wash cycle Technical data GB Care and maintenance, 16 Cutting off the water or electricity supply Cleaning the washing machine Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump Checking the water inlet hose Precautions and tips, 17 General safety Load balancing system Disposal XWA 71252 Description of the washing machine and starting a wash cycle, 18-19 Control panel Indicator lights Starting a wash cycle Wash cycles, 20 Push & Wash Table of wash cycles Personalisation, 21 Setting the temperature Setting the spin speed Functions Detergents and laundry, 22 Detergent dispenser drawer Bleach cycle Preparing the laundry Garments requiring special care Troubleshooting, 23 Service, 24 13 Installation GB !This instruction manual should be kept in a safe place for future reference. If the washing machine is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself/herself with its operation and features. [. . . ] 19 Wash cycles GB Push & Wash This function allows for starting a wash cycle even when the machine is switched off without having to press the ON/OFF button in advance, or after switching on the machine, without having activated any button and/or selector (otherwise, the Push & Wash function will be deactivated). To start the Push & Wash cycle press and hold the relative button for 2 seconds. The lit indicator light indicates that the cycle has started. This wash cycle is ideal for cotton or synthetic fabrics, as it washes at a temperature of 30° and a maximum spin speed of 1200 rpm. Load the laundry (cotton and/or synthetic garments) and close the door. Start the programme by pressing and holding the Push & Wash button for 2 seconds. The relative indicator light turns green and the door will lock (the DOOR LOCKED symbol turns on). : starting the wash cycle through the Push & Wash button activates an automatic non-customisable cycle recommended for cotton and synthetic fabrics. This programme does not allow for setting any additional options. To open the door while an automatic cycle is under way, press the START/PAUSE button; if the DOOR LOCKED symbol is switched off the door may be opened. Press the START/PAUSE button again to restart the wash cycle from the point at which it was interrupted. Once the programme is finished, the END indicator light turns on. Table of wash cycles Wash cycles Detergents Fabric softener Bleach Wash Description of the wash cycle Prewash Max. Load (kg) Total water lt 75 46 46 70 Residual dampness % Energy consumption kWh 53 2, 15 53 46 46 53 80 1, 00 0, 79 0, 56 0, 89 0, 22 - Special Sport Dark Anti-odour (Cotton) Anti-odour (Synthetic) Delicate Wool: for wool, cashmere, etc. 20° Eco Synthetic 20° Rapid Rapid 30° Rapid 60° Partials Rinse/Bleach Spin + Drain - 77 170’ 53 1, 07 52, 5 180’ - 170’ - 115’ 9’ 34 30’ 60’ The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected. 1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 8 with a temperature of 60°C. This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value. 2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 9 with a temperature of 40°C. This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value. [. . . ] € The free end of the hose is under water (see “Installation”). € The wall drainage system is not fitted with a breather pipe. If the problem persists even after these checks, turn off the water tap, switch the appliance off and contact the Assistance Service. If the dwelling is on one of the upper floors of a building, there may be problems relating to water drainage, causing the washing machine to fill with water and drain continuously. [. . . ]