User manual INFINITY BETA ES250

[. . . ] If you are using the Beta ES250 as a rear speaker in a 6- or 7channel home theater system (Application 2), please follow the directions on page 3. The Beta ES250 also possesses the unique capacity to behave as two distinct loudspeakers from one enclosure. This allows you to use a single ES250 for both the left and right rear speakers in a 7-channel system. If you are using the Beta ES250 this way, please follow the instructions on page 3 (Application 3). Left Surround Channel Left Front Channel Center Channel Infinity Right Subwoofer Front Channel (optional) Couch Right Surround Channel Figure 1. Placement (Application 1) When using the Beta ES250 for the surround channels in a 5-channel home theater system or for side channels in a 6or 7-channel home theater system, refer to Figures 1 and 2. The speakers should be placed perpendicular to or slightly behind the primary listening location, as shown. Left Front Channel Center Channel Right Front Channel Infinity Subwoofer (optional) Setting the Surround Configuration Selector It is generally recommended that the selectable surround mode configuration be set to Bipole. [. . . ] This overhead view shows a typical home theater plan when using two rear channel speakers. (BIPOLE) 5. Connect the speaker wire for the LEFT REAR speaker to the bottom set of terminals (Fig. Set the mode configuration switch to the Bipole position (Fig. Surround mode configuration switch. BETA ES250 3 WIRING THE SYSTEM IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding is usually considered positive polarity (i. e. , +). Heavier-gauge wire should be used when more than 50 feet (15m) of speaker wire is required. The wire channels on the rear of the Beta ES250 will accommodate most types of 14- to 18-gauge wire. NOTE: If desired, consult your local Infinity dealer about speaker wire and connection options. To ensure proper polarity, connect each + terminal on the back of the amplifier or receiver to the respective + (red) terminal on each speaker, as shown in Figure 8. Connect the ­ (black) terminals in a similar way. See the owner's guides that were included with your amplifier or receiver to confirm connection procedures. IMPORTANT: Do not reverse polarities (i. e. , + to ­ or ­ to +) when making connections. Doing so will cause poor imaging and diminished bass response. Receiver or Amplifier (rear view) + ­ Applications 1 and 2 (one channel shown) ­ + Speaker (rear view) Figure 8. Wiring diagram shows polarity connections for one channel using Applications 1 and 2. Application 3 Figure 9. Loosen the terminals and remove the strapping bars that connect the two sets of terminals. This example shows how to connect bare wires to the terminals. Right Rear Speaker Receiver/ Amplifier ­ + + Right Rear Left Rear ­+ ­ ­ Left Rear Speaker + Figure 10. Wiring diagram shows connections for two channels using Application 3. 4 BETA ES250 WALL-MOUNTING The Infinity Beta ES250 speaker is designed to mount directly to a wall. Each speaker has (4) keyholes in the rear to allow either left- or right-side placement. Each speaker will require (2) 1-1/2" (38mm), #8 wood screws fastened to a wall stud. If a wall stud is unavailable, install an anchor appropriate for a 1-1/2" (38mm), #8 screw. Use the supplied template to accurately position the screws on the wall and refer to the diagrams for more assistance. NOTE: The customer is responsible for the correct selection and use of mounting hardware (available through hardware stores) that will ensure the proper and safe wall-mounting of the speakers. Position the supplied wall-mount template on the wall in the desired speaker location. [. . . ] In addition, some receivers/processors allow you to adjust the high-pass frequency for the "small" or "high-pass" setting. If your receiver/processor has this capability, it is recommended that you set the highpass frequency to between 80Hz and 120Hz. Consult your receiver/processor manual for more information about these adjustments. The placement and setup instructions in this manual are written in general terms to cover most typical installations. [. . . ]