User manual INFINITY KAPPA 50.7CS 60.7CS 65.7CS 680.7CS

[. . . ] Remember to keep your sales receipt with this manual in a safe place so both are available for future reference. ABOUT THESE INSTRUCTIONS Installation of automotive stereo components can require extensive experience with a variety of mechanical and electrical procedures. Although these instructions explain how to install Kappa Series Component Systems in a general sense, they do not show the exact installation methods for your particular vehicle. If you do not feel you have the experience, do not attempt the installation yourself, but instead ask your authorized Infinity car audio dealer about professional installation options. [. . . ] · Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws. Remember that the screws can extend behind the surface. · At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. · Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl, to keep material from snagging in a drill bit or saw. · For door installations, check the clearance with the windows throughout the range of the window's travel, and verify that a mounted speaker will not interfere with the window crank or power window mechanism. · If mounting speakers elsewhere, check for clearance around rear deck torsion bars, glove box or other structural elements. · Do not mount speakers where they will get wet. · If possible, select a mounting site for the crossover network that is near the speakers and provides easy access for connections. INSTALLATION Figure 1. Mounting the 50. 7cs woofer with the grille. Figure 2. Mounting the 60. 7cs woofer with the grille. Note: The 680. 7cs is designed to replace 5" x 7" and 6" x 8" speakers installed behind existing vehicle grilles, and does not include grilles. INSTALLATION INTERMOUNT III MOUNTING RINGS The Kappa 60. 7cs is packaged with two different speaker adaptor rings. The rings will allow the speakers to be installed into various factory 6, " 6-1/2" and 6-3/4" openings. The metal ring can be mounted in many European vehicles, Japanese vehicles or vehicles with 6" speaker locations. The plastic ring can be mounted in many vehicles using 6-3/4" speaker locations or three-point mounting frames. Mounting the 65. 7cs in a 165mm speaker location using the supplied metal ring. Mounting the tweeter using the (--) SMALL LUG LOCK ANGLESCREW TO SETTINGS. BLACK I-Mount surface-mounting cup. 1 ATTACH BASE WITH SCREWS, THEN: FLUSH-MOUNT Figure 5A. Mounting the tweeter using the I-MountTM flush-mounting kit. 3 TWEETER ANGLE Figure 6. Aim the tweeter at the listening position by sliding the stud in the groove on the back of the tweeter cup and rotating the entire assembly in the mounting surface. Lock the tweeter in place, using the small retaining screw. 3 ROTATE ENTIRE ASSEMBLY TO AIM ANGLED TWEETER TOWARD LISTENER. Figure 7A. [. . . ] TWEETER LEVEL ADJUSTMENT Located on the right side of the crossover network is a small switch which controls the tweeter level. The upper position is +3dB and the lower position is 0dB. Adjust to personal preference. SPECIFICATIONS 50. 7cs Type: 5-1/4" 2-Way Component Crossover Frequency: 3. 5kHz Woofer Speaker Impedance: 2 ohms Power Handling: 85W RMS, 255W Peak Sensitivity: 94dB @ 2. 83V, 1m Frequency Response: 55Hz ­ 25kHz Mounting Depth: 2-1/16" (53mm) Cutout Diameter: 4-11/16" (120mm) Tweeter Speaker Impedance: 2 ohms Power Handling: 50W RMS, 150W Peak Sensitivity: 94dB @ 2. 83V, 1m Frequency Response: 3. 5kHz ­ 25kHz Mounting Depth: 3/4" (19mm) Cutout Diameter: 1-7/8" (48mm) 60. 7cs Type: Crossover Frequency: Woofer Speaker Impedance: Power Handling: Sensitivity: Frequency Response: Mounting Depth: Cutout Diameter: Tweeter Speaker Impedance: Power Handling: Sensitivity: Frequency Response: Mounting Depth: Cutout Diameter: 65. 7cs Type: 165mm 2-Way Component Crossover Frequency: 3. 5kHz Woofer Speaker Impedance: 2 ohms Power Handling: 90W RMS, 270W Peak Sensitivity: 95dB @ 2. 83V, 1m Frequency Response: 45Hz ­ 25kHz Mounting Depth: 2-1/4" (58mm) Cutout Diameter: 5-5/8" (143mm) Tweeter Speaker Impedance: 2 ohms Power Handling: 50W RMS, 150W Peak Sensitivity: 94dB @ 2. 83V, 1m Frequency Response: 3. 5kHz ­ 25kHz Mounting Depth: 3/4" (19mm) Cutout Diameter: 1-7/8" (48mm) 680. 7cs Type: Declaration of Conformity We, Harman Consumer Group International 2, route de Tours 72500 Chateau-du-Loir France RED TO AMPLIFIER SPEAKER OUTPUTS TO WOOFER BLK TO TWEETER 6-1/2" 2-Way Component 3. 5kHz 2 ohms 90W RMS, 270W Peak 95dB @ 2. 83V, 1m 45Hz ­ 25kHz 2-3/ 16" (56mm) 5" (127mm) 2 ohms 50W RMS, 150W Peak 94dB @ 2. 83V, 1m 3. 5kHz ­ 25kHz 3/4" (19mm) 1-7/8" (48mm) declare in own responsibility that the products described in this owner's manual are in compliance with technical standards: EN 61000-6-3:2001 EN 61000-6-1:2001 Klaus Lebherz Harman Consumer Group International Chateau-du-Loir, France 2/05 Figure 8B. Locating wiring connections on the woofer. Big Lug = Small Lug = 6" x 8"/5" x 7" 2-Way Component Crossover Frequency: 3. 5kHz Woofer Speaker Impedance: 2 ohms Power Handling: 90W RMS, 270W Peak Sensitivity: 94dB @ 2. 83V, 1m Frequency Response: 40Hz ­ 25kHz Mounting Depth: 2-1/4" (58mm) Cutout Diameter: 7-1/8" x 4-7/8" (181mm x 124mm) Tweeter Speaker Impedance: 2 ohms Power Handling: 50W RMS, 150W Peak Sensitivity: 94dB @ 2. 83V, 1m Frequency Response: 3. 5kHz ­ 25kHz Mounting Depth: 3/4" (19mm) Cutout Diameter: 1-7/8" (48mm) Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA 516. 674. 4463 · FAX 516. 682. 3523 · www. infinitysystems. com © 2005 Harman International Industries, Incorporated · Part No. [. . . ]