User manual INFINITY KAPPA PERFECT 6-1

[. . . ] 6. 1 6. 5" Component System INSTRUCTIONS ® KAPPASERIES Thank you for purchasing an Infinity Kappa Perfect component system. The Kappa Perfect6. 1 has been engineered to provide the most accurate sonic reproduction possible. Over the years, we at Infinity have listened to hundreds of automotive speakers and we think these are the best. [. . . ] Infinity accepts no liability for hearing loss, bodily injury or property damage resulting from use or misuse of this product. TWEETER and WOOFER on kick panel WOOFER in factorydoor location Figure 5. Surface-mounting the tweeter Figure 1. Fig 1 Mounting the woofer and tweeter in the kick panels Figure 3. Fig 3 Mounting the woofer and tweeter in the doors A NOTE ABOUT SYSTEM PERFORMANCE For the best performance possible, the Kappa Perfect6. 1 should be used with a two-channel amplifier with output power of at least 35W RMS per channel. The passive crossover contains impedance-compensating circuitry and has been computer-optimized for the flattest possible frequency response with the tweeter flush-mounted on axis with the listener. The combined responses of the speakers and passive crossover constitute 4th-order Linquitz-Riley acoustic alignment and cannot be duplicated with any electronic crossover currently available for car-audio use. Consequently, bi-amping the Perfect6. 1 with an electronic crossover is not recommended. TWEETER on dash 1 2 TWEETER on kick panel WOOFER in factorydoor location WOOFER in factorydoor location Figure 6. Flush-mounting the tweeter Fig 4 Figure 2. Mounting the woofer in the door and the tweeter in the kick panel Fig 2 Figure 4. Mounting the woofer in the door and the tweeter in the dash WOOFER INSTALLATION ELECTRICAL CONNECTIONS AND CROSSOVER ADJUSTMENTS SPECIFICATIONS System Frequency Response: Power Handling: Nominal Impedance: Sensitivity: Crossover Frequency: 75Hz ­ 23kHz, ±3dB 100W RMS, 400W Peak 4 Ohms 90dB 3. 5kHz, 24dB/oct. Linquitz-Riley Acoustic Tweeter level ­4dB J1 J2 Tweeter level +5dB J1 J2 J1 Figure 7. Mounting the woofer where there is no factory speaker location Tweeter level 0dB (default) J1 J2 ® Figure 8. Mounting the woofer in standard 5-1/4" holes (in many Japanese and American automobiles) TWEETER LEVEL ­4dB 0dB +5dB J1 J2 J1 J2 ® KPX00 To amplifier speaker output To woofer To tweeter Figure 11. Adjust the crossover using the jumpers provided Thiele and Small Parameters Woofer Tweeter Revc: 3. 45 3. 31 Levc: 0. 37 0. 02 Sd: 0. 0113 0. 0005 BL: 6. 37 1. 99 Vas: 11. 43 0. 0016 Cms: 630. 36 44 Mms: 18. 94 0. 3064 Mmd: 18. 25 0. 3 Fs: 46. 05 1370. 65 Qms: 3. 44 5. 4 Qes: 0. 465 2. 19 Qts: 0. 41 1. 56 Top-Plate Thickness: 9/32" (7. 115mm) na Voice-Coil Length: 9/16" (14mm) na Voice-Coil Diameter: 1-1/2" (38. 1mm) 1" (25. 4mm) Xmax: 1/8" (3. 44mm) na Mounting Depth: 2-3/4" (70mm) 1" (25. 4mm) Cut-Out Diameter: 5-1/16" (129mm) 1-3/4" (45mm) Figure 10. [. . . ] Component frequency response Figure 15. Woofer and tweeter impedance Infinity Systems, Inc. · 250 Crossways Park Drive Woodbury, NY 11797 USA · (800) 553-3332 FAX (516) 682-3523 · Part No: KAP6. 1OM A Harman International Company [. . . ]