User manual INFINITY KAPPA PERFECT51 PERFECT61

[. . . ] kappa series perfect5 . 1 perfect6 . 1 Thank you for purchasing an Infinity Kappa Perfect component system. Kappa Perfect components have been engineered to provide the most accurate sonic reproduction possible. [. . . ] We recommend listening at low volume while driving. Infinity accepts no liability for hearing loss, bodily injury or property damage resulting from use or misuse of this product. Surface-mounting the tweeter TWEETER and WOOFER on kick panel WOOFER in factorydoor location A NOTE ABOUT SYSTEM PERFORMANCE For the best performance possible, the Kappa Perfect components should be used with a two-channel amplifier with output power of at least 50W RMS per channel. The passive crossover contains impedancecompensating circuitry and has been computer-optimized for the flattest possible frequency response with the tweeter flushmounted, on-axis with the listener. The combined responses of the speakers and passive crossover constitute a 4th-order Linquitz-Riley acoustic alignment and cannot be duplicated with any electronic crossover currently available for car audio use. Consequently, bi-amping a Perfect component system with an electronic crossover is not recommended. Figure 1. Fig 1 Mounting the woofer and tweeter in the kick panels Figure 3. Fig 3 Mounting the woofer and tweeter in the doors blk red 1 ­ + TWEETER on dash TWEETER on kick panel 2 WOOFER in factorydoor location WOOFER in factorydoor location Figure 6. Flush-mounting the tweeter Fig 4 Figure 2. Mounting the woofer in the door and the tweeter in the kick panel Fig 2 Figure 4. Mounting the woofer in the door and the tweeter in the dash -2- WOOFER INSTALLATION ELECTRICAL CONNECTIONS AND CROSSOVER ADJUSTMENTS DECLARATION OF CONFORMITY Tweeter level 4dB J1 J2 We, Harman Consumer International 2, route de Tours 72500 Chateau-du-Loir France declare in own responsibility, that the products described in this owner's manual are in compliance with technical standards: EN 50081-1:1992 EN 50082-1:1997 Lutz Uphoff Harman Consumer International Chateau-du-Loir, France 4/01 Tweeter level +5dB J1 J2 J1 Figure 7. Mounting the P5. 1 or P6. 1 woofer where there is no factory speaker location. [. . . ] Linquitz-Riley Acoustic SYSTEM RESPONSE CURVES Perfect6. 1 System Frequency Response 110 dB spl Perfect5. 1 System Frequency Response Deg Sound Pressure Level 180 100 dB spl < Magnitude > Sound Pressure Level < Phase > Deg 180 100 135 90 135 90 90 80 90 80 45 70 45 70 0 60 0 Thiele and Small Parameters P6. 1 Woofer Revc: 3. 45 Levc: 0. 37 Sd: 0. 0113 BL: 6. 37 Vas: 11. 43 Cms: 630. 36 Mms: 18. 94 Mmd: 18. 25 Fs: 46. 05 Qms: 3. 44 Qes: 0. 465 Qts: 0. 41 Top-Plate Thickness: 9/32" (7. 115mm) Voice-Coil Length: 9/16" (14mm) Voice-Coil Diameter: 1-1/2" (38. 1mm) Xmax: 1/8" (3. 44mm) Mounting Depth: 2-3/4" (70mm) Cut-Out Diameter: 5-1/16" (129mm) 60 -45 50 -45 P5. 1 Woofer 3. 38 0. 21 0. 0100 3. 94 9. 29 654. 21 10. 41 9. 84 60. 98 3. 60 0. 87 0. 701 9/32" (7. 115mm) 9/16" (14mm) 1-1/4" (31. 75mm) 1/8" (3. 44mm) 2-3/8" (61mm) 4-5/8" (118mm) Tweeter 3. 31 0. 02 0. 0005 1. 99 0. 0016 44 0. 3064 0. 3 1370. 65 5. 4 2. 19 1. 56 N/A N/A 1" (25. 4mm) N/A 1" (25. 4mm) 1-3/4" (45mm) 50 -90 40 -90 40 -135 30 -135 30 20 Fr e que nc y 100 500 1k Hz 5k 10k C -180 20 C 20k 20 Frequency 100 500 1k Hz 5k 10k 20k -180 Kappa Perfect6. 1 (flat setting) Kappa Perfect6. 1 (+5dB setting) Kappa Perfect6. 1 (­4dB setting) Kappa Perfect6. 1 (flat setting) Kappa Perfect6. 1 (+5dB setting) Kappa Perfect6. 1 (­4dB setting) Perfect6. 1 System Impedance 30. 0 Ohms < Magnitude > Impedance Measurement < Phase > Deg 180 Perfect5. 1 System Impedance 30. 0 Ohms < Magnitude > Impedance Measurement < Phase > Deg 180 135 135 10. 0 90 10. 0 90 45 45 3. 0 0 3. 0 0 -45 -45 1. 0 -90 1. 0 -90 -135 -135 0. 3 C 20 Frequency 100 500 1k Hz 5k 10k 20k -180 0. 3 C 20 Frequency 100 500 1k Hz 5k 10k 20k -180 Infinity Systems, Inc. , 250 Crossways Park Drive, Woodbury, NY 11797 USA (800) 553-3332 · FAX (516) 682-3523 · www. infinitysystems. com © 2001 Infinity Systems, Inc. · Part No. : KAP5. 1/6. 1OM4/01 · Printed 4/01 [. . . ]