User manual INFINITY OREUS

[. . . ] The foot supplied with your Oreus satellites and center channel is supplied assembled. PLACEMENT NOTE: The satellite speakers can be placed directly on a shelf, or mounted on a wall using the built-in base/bracket. CAUTION: The rubber feet can under certain conditions smudge or discolor light colored and delicate surfaces. Please place a protective mat or coaster under the rubber feet to prevent marking or discoloration. Fit the five self-adhesive rubber feet to the foot. For front left and right channels For front left and right channels, place one satellite to the left and another to the right of the television, as shown in Figure 1. Since the speakers are magnetically shielded, you can place them very close to the TV without worrying about the magnetic field distorting the picture. Center Channel For the center channel, place the speaker directly on top of, or below, your television. [. . . ] Use the hex key supplied to loosen the screws. 3. Attach the base to the wall using suitable screws. Your speaker should now look like this. 4 5. CAUTION: please remember that your Oreus speakers are heavy and must be adequately secured to the wall to avoid the risk of injury being caused should they fall. Use longer fixing screws and suitable wall plugs if necessary. 6. Feed the speaker cable through the cable-entry hole in the base and then through the pivot. 3. Connect the cable to the speaker terminals. Speaker cable is usually colour-coded (red or white for positive) or provided with an identifying stripe or rib on the positive conductor. Connect the positive conductor to the red speaker terminal. Insert the pivot into one or other of the two pivot holes in the speaker, depending on whether you wish to use the speaker vertically or horizontally. Fit the blanking plug into the unused pivot location hole and then re-fit the rear cover on the speaker. If you want to hide the speaker cables in the wall you can use the cable entry hole in the underside of the base. Adjust the angle of your speaker 1. You can tilt your speaker up or down on its foot and you can also rotate it. If you experience difficulty tilting or rotating your speaker, try loosening the fixing screws for the pivot cover plate on the foot. Re-fit the cover plate and replace the two fixing screws. Do not fully tighten the screws at this stage because you will need to rotate the pivot later in the assembly proceedure to angle your speakers correctly. Attach the foot to the speaker 1. Remove the two screws and take off the rear cover plate from the the speaker. Use the hex key supplied to loosen the screws. Once you have adjusted your speaker the way you want it, fully tighten the fixing screws of the pivot cover plate on the foot. This will hold your chosen adjustment ASSEMBLING THE FLOORSTAND Assembling the stand 1. The Oreus stand is supplied with the base detached from the column. The foot can be attached to the speaker at two different positions. [. . . ] This is not entirely true. A subwoofer is there to enhance bass, extending the response of the entire system so that bass can be felt as well as heard. Auto-On Signal Sensing The Oreus Subwoofer incorporates automatic signal-sensing circuitry which turns the subwoofer on instantly when an audio signal is present. When a signal has not been detected for approximately 1. 5 minutes, the subwoofer automatically goes into standby mode. 8 ACOUSTIC FEEDBACK If the bass seems boomy, or you notice a rumbling sound when listening to record albums, the cause may be acoustic feedback. This means that low-frequency vibrations from your speakers are reaching the turntable. To help isolate the turntable from these vibrations, place the turntable on a heavy, solid support, as far away as possible from the subwoofer. If you continue to experience difficulties after experimenting with placement, consult your Infinity dealer. SPECIFICATIONS Oreus HCS Frequency Response: Recommended Amplifier: Sensitivity: (2. 83V @ 1 meter) Crossover Frequency: LF Drive Unit: Satellite 95 Hz ­ 22 Khz (±3dB) 25 ­ 100 Watts 85 dB Important! CD/DVD players are also susceptible to vibrations and should be placed on solid supports to isolate them acoustically. [. . . ]