User manual INFINITY REFERENCE 4012I 5012I 6012I 6012SI 9612I 9613I 3012CF 6412CF 6412CFP 6812CF

[. . . ] Remember to keep your sales receipt with this manual in a safe place so both are available for future reference. IMPORTANT: Installation of automotive stereo components can require extensive experience with a variety of mechanical and electrical procedures. Although these instructions explain how to install Reference Series speakers in a general sense, they do not show the exact installation methods for your particular vehicle. [. . . ] · Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws. Remember that the screws can extend behind the surface. · At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. CAUTION: In some cars, fuel tanks may be located directly beneath the rear deck. Check for adequate speaker basket clearance before considering this location!· Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl, to keep material from snagging in a drill bit or saw. · For door installations, check the clearance with the windows throughout the range of the window's travel, and verify that a mounted speaker will not interfere with the window crank or power window mechanism. · If mounting speakers elsewhere, check for clearance around rear deck torsion bars, glove box or other structural elements. · Do not mount speakers where they will get wet. INSTALLATION Figure 1. Mounting the Reference Series speakers using supplied grille. Note:The 3012cf, 6412cf, 6412cfp and 6812cf speakers are designed to be installed under factory grilles. Consequently, no grilles are packaged with these models. Modifying the 4012i to be installed in locations requiring fewer than 4 mounting "ears" . [. . . ] 6, 505, 705) The 6012i and 6012si are packaged with two different speaker adaptor rings. These are used to install the 6-1/2" speakers in various vehicles. The metal ring can be mounted in many European vehicles, while the plastic ring can be mounted in many vehicles using 6-3/4" speaker locations or three-point mounting frames. FOAM GASKET FOAM GASKET MOUNTING RING reference series SPECIFICATIONS 4012i Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 5012i Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 6012i Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 4" 2-Way 4 Ohms 35W RMS, 105W Peak 85Hz ­ 21kHz 91dB 1-7/8" (48mm) 3-3/4" (96mm) 6012si Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 9612i Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 6-1/2" Shallow-Mount 2-Way 4 Ohms 50W RMS, 150W Peak 53Hz ­ 21kHz 92dB 1-15/16" (50mm) 5" (127mm) 3012cf Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 6412cf Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 3-1/2" 2-Way 4 Ohms 25W RMS, 75W Peak 85Hz ­ 21kHz 90dB 1-7/16" (37mm) 3-1/16" (78mm) 6812cf Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 6" x 8"/5" x 7" 2-Way 4 Ohms 60W RMS, 180W Peak 49Hz ­ 21kHz 92dB 2-7/16" (62mm) 5" x 7-3/16" (127mm x 183mm) 5-1/4" 2-Way 4 Ohms 45W RMS, 135W Peak 67Hz ­ 21kHz 91dB 2-1/4" (58mm) 4-11/16" (120mm) 6" x 9" 2-Way 4 Ohms 100W RMS, 300W Peak 46Hz ­ 21kHz 92dB 3" (77mm) 6-1/16" x 8-7/8" (154mm x 226mm) 4" x 6" 2-Way 4 Ohms 40W RMS, 120W Peak 72Hz ­ 21kHz 91dB 1-15/16" (50mm) 3-5/8" x 5-5/8" (93mm x 143mm) 6-1/2" 2-Way 4 Ohms 60W RMS, 180W Peak 53Hz ­ 21kHz 92dB 2-1/16" (53mm) 5" (127mm) 9613i Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 6" x 9" 3-Way 4 Ohms 100W RMS, 300W Peak 46Hz ­ 21kHz 92dB 3" (77mm) 6-1/16" x 8-7/8" (154mm x 226mm) 6412cfp Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Mounting Depth: Cutout Diameter: 4" x 6" 2-Way Plate 4 Ohms 45W RMS, 135W Peak 72Hz ­ 21kHz 91dB 1-15/16" (50mm) 3-9/16" x 5-11/16" (91mm x 145mm) Declaration of Conformity A valid serial number is required for warranty coverage. [. . . ]