User manual INFINITY REFERENCE 42.7I 52.7I 62.7I 63.7I 652.7I 653.7I 692.7I 693.7I 32.7CF 462.7CFP 682.7CF

[. . . ] Remember to keep your sales receipt with this manual in a safe place so both are available for future reference. ABOUT THESE INSTRUCTIONS Installation of automotive stereo components can require extensive experience with a variety of mechanical and electrical procedures. Although these instructions explain how to install Kappa Series multi-element speakers in a general sense, they do not show the exact installation methods for your particular vehicle. If you do not feel you have the experience, do not attempt the installation yourself, but instead ask your authorized Infinity car audio dealer about professional installation options. [. . . ] · Keep speakers in their package until final installation. When moving a speaker, always rest it with the cone or dome facing up. · Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws. Remember that the screws can extend behind the surface. · At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. · Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl, to keep material from snagging in a drill bit or saw. · For door installations, check the clearance with the windows throughout the range of the window's travel, and verify that a mounted speaker will not interfere with the window crank or power window mechanism. · If mounting speakers elsewhere, check for clearance around rear deck torsion bars, glove box or other structural elements. · Do not mount speakers where they will get wet. INSTALLATION Figure 1. Mounting the 42. 7i, 52. 7i, 62. 7i, 63. 7i, 692. 7i, 693. 7i, 32. 7cf or 682. 7cf. NOTE:The 32. 7cf, 462. 7cfp and 682. 7cf speakers are designed to be installed under factory grilles. Consequently, no grilles are packaged with these models. The 32. 7cf (not shown) is mounted in a similar way. FOAM GASKET Figure 3a. Figure 2. Modifying the 42. 7i to be installed in locations requiring fewer than 4 mounting "ears" . (The 62. 7i and 63. 7i may be similarly modified. ) NOTE: Grip the tab with pliers and bend to detach it from the speaker. FOAM GASKET INSTALLATION Figure 4. Mounting the 62. 5i in a standard speaker location. INTERMOUNT III MOUNTING RINGS The Kappa 62. 7 and 63. 7 speakers are packaged with two different speaker adaptor rings. [. . . ] Other speaker models are connected in a similar way. Tweeter terminals on top Yellow Green 1 2 Figure 5. Mounting the 62. 5i in a 165mm speaker location. FOAM GASKET Woofer terminals on bottom White Blue Figure 7. Tweeter level adjustment. PUSH BUTTON NOTE: The positions shown here for the polarities may not resemble the exact connections in every installation. However, in every case, the larger terminal is the positive (+) connection. Red Black FOAM GASKET INTERMOUNT RING kappa series SPECIFICATIONS 42. 7i Type: Speaker Impedance: Power Handling: Sensitivity (2. 83V, 1m): Frequency Response: Mounting Depth: Cut-Out Diameter: 52. 7i Type: Speaker Impedance: Power Handling: Sensitivity (2. 83V, 1m): Frequency Response: Mounting Depth: Cut-Out Diameter: 62. 7i Type: Speaker Impedance: Power Handling: Sensitivity (2. 83V, 1m): Frequency Response: Mounting Depth: Cut-Out Diameter: 4" 2-Way 2 ohms 50W RMS, 150W Peak 93dB 75Hz ­ 25kHz 1-13/16" (47mm) 3-7/16" (88mm) 63. 7i Type: Speaker Impedance: Power Handling: Sensitivity (2. 83V, 1m): Frequency Response: Mounting Depth: Cut-Out Diameter: 652. 7i Type: Speaker Impedance: Power Handling: Sensitivity (2. 83V, 1m): Frequency Response: Mounting Depth: Cut-Out Diameter: 653. 7i Type: Speaker Impedance: Power Handling: Sensitivity (2. 83V, 1m): Frequency Response: Mounting Depth: Cut-Out Diameter: 6-1/2" 3-Way 2 ohms 75W RMS, 225W Peak 95dB 45Hz ­ 25kHz 2-3/16" (56mm) 5" (127mm) 692. 7i Type: Speaker Impedance: Power Handling: Sensitivity (2. 83V, 1m): Frequency Response: Mounting Depth: Cut-Out Diameter: 6" x 9" 2-Way 2 ohms 110W RMS, 330W Peak 95dB 35Hz ­ 25kHz 3-3/16" (81mm) 5-7/ 8" x 8-11/ 16" (150mm x 221mm) 462. 7cfp Type: Speaker Impedance: Power Handling: Sensitivity (2. 83V, 1m): Frequency Response: Mounting Depth: Cut-Out Diameter: 4" x 6" 2-Way, Custom-Fit Plate 2 ohms 60W RMS, 180W Peak 94dB 75Hz ­ 25kHz 1- 13/16" (47mm) 3-5/8" x 5-3/8" (93mm x 137mm) 5-1/4" 2-Way 2 ohms 55W RMS, 165W Peak 94dB 55Hz ­ 25kHz 2-1/16" (53mm) 4-11/16" (120mm) 165mm 2-Way 2 ohms 75W RMS, 225W Peak 95dB 45Hz ­ 25kHz 2-1/4" (58mm) 5-5/8" (143mm) 693. 7i Type: Speaker Impedance: Power Handling: Sensitivity (2. 83V, 1m): Frequency Response: Mounting Depth: Cut-Out Diameter: 6" x 9" 3-Way 2 ohms 110W RMS, 330W Peak 95dB 35Hz ­ 25kHz 3-3/16" (81mm) 5-7/ 8" x 8-11/ 16" (150mm x 221mm) 682. 7cf Type: Speaker Impedance: Power Handling: Sensitivity (2. 83V, 1m): Frequency Response: Mounting Depth: Cut-Out Diameter: 6-1/2" 2-Way 2 ohms 75W RMS, 225W Peak 95dB 45Hz ­ 25kHz 2-3/16" (56mm) 5" (127mm) 165mm 3-Way 2 ohms 75W RMS, 225W Peak 95dB 45Hz ­ 25kHz 2-1/4" (58mm) 5-5/8" (143mm) 32. 7cf Type: Speaker Impedance: Power Handling: Sensitivity (2. 83V, 1m): Frequency Response: Mounting Depth: Cut-Out Diameter: 6" x 8, 5" x 7" 2-Way, " Custom-Fit 2 ohms 100W RMS, 300W Peak 94dB 40Hz ­ 25kHz 2-1/4" (58mm) 4-7/8" x 7-1/ 8" (124mm x 181mm) 3-1/2" 2-Way, Custom-Fit 2 ohms 35 W RMS, 105W Peak 95dB 85Hz ­ 25kHz 1- 9/16" (40mm) 3-1/4" (83mm) Declaration of Conformity A valid serial number is required for warranty coverage. Features, specifications and appearance are subject to change without notice. [. . . ]