User manual INFINITY REFERENCE 5010CS 6010CS 6810CS

[. . . ] Remember to keep your sales receipt with this manual in a safe place so both are available for future reference. IMPORTANT: Installation of automotive stereo components can require extensive experience with a variety of mechanical and electrical procedures. Although these instructions explain how to install Reference Series speakers in a general sense, they do not show the exact installation methods for your particular vehicle. [. . . ] Remember that the screws can extend behind the surface. · At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines, and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. CAUTION: In some cars, fuel tanks may be located directly beneath the rear deck. Check for adequate speaker basket clearance before considering this location!· Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl, to keep material from snagging in a drill bit or saw. · For door installations, check the clearance with the windows throughout the range of the window's travel, and verify that a mounted speaker will not interfere with the window crank or power window mechanism. · If mounting speakers elsewhere, check for clearance around rear deck torsion bars, glove box, or other structural elements. · Do not mount speakers where they will get wet. INSTALLATION Figure 1. Mounting the 5010cs woofer with the grille. Mounting the 6010cs in 165mm speaker locations. FOAM GASKET Figure 2. Mounting the 6010cs woofer with the grille. MOUNTING RING INTERMOUNT III (PATENT NO. 6, 505, 705) The 6010cs is packaged with two different speaker adaptor rings. These are used to install the 6-1/2" speakers in various vehicles. The metal ring can be mounted in many European vehicles, while the plastic ring can be mounted in many vehicles using 6-3/4" speaker locations or three-point mounting frames. Mounting the 6010cs woofer in standard speaker locations. Note: The 6810cs is designed to replace 5" x 7" and 6" x 8" speakers installed behind existing vehicle grilles, and does not include grilles. FOAM GASKET INSTALLATION FLUSH-MOUNT Figure 5A. Mounting the tweeter using the I-MountTM (patent no. 5, 859, 917) flush-mounting kit. 3 TWEETER ANGLE Figure 6. 3 ROTATE ENTIRE ASSEMBLY TO AIM ANGLED TWEETER TOWARD LISTENER. Figure 7A. [. . . ] Use glue if clearance is an issue. reference series Note: Not all possible mounting configurations are shown. CONNECTIONS Connect the speakers to the crossover and the crossover to the amplifier, observing proper polarity. Figure 8A. p/s 050 2ohm 5. 4uF SPECIFICATIONS 5010cs Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Crossover Frequency: Mounting Depth: Cut-out Diameter: 5-1/4" 2-Way Component System 4 Ohms 75W RMS, 225W Peak 67Hz ­ 21kHz 91dB 3. 5kHz Woofer: 2-1/4" (58mm) Tweeter: 5/8" (16mm) Woofer: 4-11/16" (120mm) Tweeter: 1-3/4" (45mm) 6810cs Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Crossover Frequency: Mounting Depth: Cut-out Diameter: 6" x 8"/5" x 7" 2-Way Component System 4 Ohms 90W RMS, 270W Peak 49Hz ­ 21kHz 92dB 3. 5kHz Woofer: 2-7/16" (62mm) Tweeter: 5/8" (16mm) Woofer: 5" x 7-1/4" (127mm x 185mm) Tweeter: 1-3/4" (45mm) 6. 8uF 2ohm 0. 22mH 0. 15mH - IN + - WF + - TW + -3dB _ + TO AMPLIFIER + _+ _ TO TWEETER SPEAKER OUTPUTS TO WOOFER Note: To reduce tweeter output level, connect the positive (+) tweeter wire to the ­3dB terminal. Figure 8B. 6010cs Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity (2. 83V, 1m): Crossover Frequency: Mounting Depth: Cut-out Diameter: 6-1/2" 2-Way Component System 4 Ohms 90W RMS, 270W Peak 53Hz ­ 21kHz 92dB 3. 5kHz Woofer: 2-1/16" (53mm) Tweeter: 5/8" (16mm) Woofer: 5" (127mm) Tweeter: 1-3/4" (45mm) A valid serial number is required for warranty coverage. [. . . ]