User manual INFINITY REFERENCE 505CS 605CS 105T

[. . . ] Reference ¤ ¤ reference series 505cs , 605cs & 105t instructions for purchasing Infinity's Reference Series automotive loudspeaker components. We've organized this manual to make your installation as simple and trouble-free as possible. Please read it thoroughly before proceeding. [. . . ] Disconnect the (­) negative lead from your vehicle's battery. · Keep speakers in their package until final installation. When moving a speaker, always rest it with the cone or dome facing up. · Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws. Remember that the screws can extend behind the surface. · At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines, and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. CAUTION: In some cars, fuel tanks may be located directly beneath the rear deck. Check for adequate speaker basket clearance before considering this location!· Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl, to keep material from snagging in a drill bit or saw. · For door installations, check the clearance with the windows throughout the range of the window's travel, and verify that a mounted speaker will not interfere with the window crank or power window mechanism. · If mounting speakers elsewhere, check for clearance around rear deck torsion bars, glove box, or other structural elements. · Do not mount speakers where they will get wet. INSTALLATION Figure 1. Mounting the 505cs woofer. INSTALLATION Figure 2. [. . . ] Lock the tweeter in place, using the small retaining nut and the large plastic mounting nut. Mounting the 605cs in 165mm speaker locations. 0. 22mH 0. 15mH - IN + - WF + - TW + -3dB CONNECT + WIRE HERE TO REDUCE TWEETER OUTPUT LEVEL + TO AMPLIFIER + _+ _ TO TWEETER SPEAKER OUTPUTS TO MID-BASS _ 3 ROTATE TO AIM ANGLED TWEETER TO LISTENER Figure 7B. 1 SLIDE UP OR DOWN TO ADJUST TWEETER ANGLE 2 TIGHTEN NUT AND WASHER TO LOCK THE ANGLE SETTINGS BIG LUG IS POSITIVE (+) SMALL LUG IS NEGATIVE (­) -3- SPECIFICATIONS 505cs Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity: Crossover Frequency: Mounting Depth: Cut-out Diameter: 5-1/4" 2-Way Component System 4 Ohms 75W RMS, 225W Peak 72Hz ­ 20kHz 92dB 3. 5kHz Woofer: 2-1/4" (58mm) Tweeter: 1-3/16" (31mm) Woofer: 4-5/8" (118mm) Tweeter: 1-3/4" (45mm) 605cs Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity: Crossover Frequency: Mounting Depth: Cut-out Diameter: 6-1/2" 2-Way Component System 4 Ohms 90W RMS, 270W Peak 54Hz ­ 20kHz 92dB 3. 5kHz Woofer: 2-1/16" (53mm) Tweeter: 1-3/16" (31mm) Woofer: 5" (127mm) Tweeter: 1-3/4" (45mm) 105t Type: Speaker Impedance: Power Handling: Frequency Response: Sensitivity: Crossover Frequency: Mounting Depth: Cut-out Diameter: 1" Tweeter 4 Ohms 50W RMS, 150W Peak 2. 5kHz ­ 20kHz 91dB 3. 5kHz 1-3/16" (31mm) 1-3/4" (45mm) DECLARATION OF CONFORMITY Infinity Systems, Inc. · 250 Crossways Park Drive Woodbury, NY 11797 USA · (800) 553-3332 · FAX (516) 682-3523 P/N: REFSERCS/TOM We, Harman Consumer International 2, Route de Tours 72500 Chateau-du-Loir France declare in own responsibility, that the products described in this owner's manual are in compliance with technical standards: EN 50081-1:1992 Lutz Uphoff EN 50082-1:1992 Harman Consumer International 12/99 [. . . ]