User manual INFINITY SW-12

[. . . ] For products intended to operate from battery power, or other sources, refer to the operating instructions. If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. [. . . ] P/N:352153-001 POWER ON < OFF R ¤ L HIGH LEVEL OUT Infinity Systems Northridge, CA USA AC 120V ~ 60HZ 500W _ + Bass Optimization Controls (see page 5) ¡ Bass Optimization System Selector TM Center-Frequency Adjustment £ Bass Optimization System Level Adjustment ¢ Bass Optimization System Bandwidth Adjustment Phase Switch § Normal/LFE Selector ¶ Power Indicator · Crossover Adjustment ª Subwoofer Level (Volume) Control , Line-Level Inputs / High-Level (Speaker) Inputs ¤ High-Level (Speaker) Outputs < Power Switch SW-12 2 CONNECTIONS If you have a Dolby* Digital or DTS® receiver/processor with a low-frequency-effects (LFE) output: If your receiver/amplifier does not have subwoofer outputs for the left and right channels or an LFE output: SUBWOOFER OR LFE OUTPUT RECEIVER/AMPLIFIER Front Speaker Output BASS OPTIMIZATION SYSTEM FREQUENCY 180 PHASE 0 LFE Normal LEVEL ON OFF POWER WIDTH GREEN: ON RED: STANDBY 50 150 CROSSOVER MIN MAX LEVEL ® BASS OPTIMIZATION SYSTEM LINE LEVEL IN R L SW-12 CAUTION R HIGH LEVEL IN L RISK OF ELECTRIC SHOCK DO NOT OPEN FREQUENCY 180 PHASE Normal 0 LFE LEVEL ON OFF POWER WIDTH WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. POWER ON OFF 0 GREEN: ON RED: STANDBY AVERTISSEMENT: POUR PRÉVENIR LES RISQUES D'INCENDIE OU DE CHOC ÉLECTRIQUE, ÉVITER D'EXPOSER CET APPAREIL A LA PLUIE OU A L'HUMIDITÉ. P/N:352153-001 50 150 CROSSOVER MIN MAX LEVEL ® R HIGH LEVEL OUT L Infinity Systems Northridge, CA USA AC 120V ~ 60HZ 500W LINE LEVEL IN R L R HIGH LEVEL IN L SW-12 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN _ + WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. POWER ON OFF AVERTISSEMENT: POUR PRÉVENIR LES RISQUES D'INCENDIE OU DE CHOC ÉLECTRIQUE, ÉVITER D'EXPOSER CET APPAREIL A LA PLUIE OU A L'HUMIDITÉ. P/N:352153-001 · Set Normal/LFE Switch to LFE. _ + R HIGH LEVEL OUT L Infinity Systems Northridge, CA USA AC 120V ~ 60HZ 500W NOTE: In this case, you do not need to use a Y connector. Simply connect the LFE output on your receiver/processor to either the left or right input on the subwoofer. If your receiver/processor has subwoofer outputs for the left and right channels: · Set Normal/LFE Switch to Normal. RECEIVER/PROCESSOR RED = + BLACK = BASS OPTIMIZATION SYSTEM ­ 1. LOOSEN TERMINALS FREQUENCY 180 PHASE 0 LFE OFF POWER Normal LEVEL ON GREEN: ON RED: STANDBY WIDTH 2. INSERT BARE END; TIGHTEN TERMINALS 50 150 CROSSOVER MIN MAX LEVEL ® LINE LEVEL IN R L R HIGH LEVEL IN L SW-12 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN STRIPE = POWER ON OFF ­ NO STRIPE = + WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. AVERTISSEMENT: POUR PRÉVENIR LES RISQUES D'INCENDIE OU DE CHOC ÉLECTRIQUE, ÉVITER D'EXPOSER CET APPAREIL A LA PLUIE OU A L'HUMIDITÉ. P/N:351153-001 R HIGH LEVEL OUT L Infinity Systems Northridge, CA USA AC 120V ~ 60HZ 500W _ + · Set Normal/LFE Switch to Normal. NOTE: Some receivers have a single subwoofer output (do not confuse this with a single LFE output as described below). In that case, it is recommended that you use a Y connector (not included) to maximize performance. 3 SW-12 OPERATION Power On Plug your subwoofer's AC cord into a wall outlet. Do not use the outlets on the back of the receiver. Initially set the Subwoofer Level (Volume) Control ª to the "min" position. Turn on your sub by pressing the Power Switch < on the rear panel. Crossover Adjustments NOTE: This control will have no effect if the Normal/LFE Selector Switch § is set to "LFE. " If you have a Dolby Digital or DTS processor/receiver, the Crossover Frequency is set by the processor/receiver. Consult your owner's manual to learn how to view or change this setting. Use a selection that has ample bass information. Set the overall volume control of the preamplifier or stereo to a comfortable level. Adjust the Subwoofer Level (Volume) Control ª until you obtain a pleasing blend of bass. Bass response should not overpower the room but rather be adjusted so there is a harmonious blend across the entire musical range. Many users have a tendency to set the subwoofer volume too loud, adhering to the belief that a subwoofer is there to produce lots of bass. This is not entirely true. A subwoofer is there to enhance bass, extending the response of the entire system so the bass can be felt as well as heard. However, overall balance must be maintained or the music will not sound natural. An experienced listener will set the volume of the subwoofer so its impact on bass response is always there but never obtrusive. SW-12 4 BASS OPTIMIZATION SYSTEMTM Infinity's Bass Optimization System is a simple-to-use, yet sophisticated, low-frequency calibration system. The subwoofer contains a parametric equalizer that you can adjust following the directions below. By following these instructions, you can improve the sound of your system. [. . . ] If your dealer does not stock the Bass Optimization System test and measurement kit, you may purchase it directly from Infinity. residents can visit our Web site at www. infinitysystems. com or call 1. 516. 674. 4INF. MAINTENANCE AND SERVICE The enclosure and grille may be cleaned using a soft cloth to remove fingerprints or to wipe off dust. All wiring connections should be inspected and cleaned or remade periodically. The frequency of maintenance depends on the metals involved in the connections, atmospheric conditions, and other factors, but once per year is the minimum. If a problem occurs, make sure that all connections are properly made and clean. [. . . ]