User manual INFOCUS IN2126A

[. . . ] Declaration of Conformity Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Suite 200, Portland, Oregon 97223-8368 USA We declare under our sole responsibility that this projector conforms to the following directives and norms: ErP Directive 2009/125/EC EMC Directive 2004/108/EC EMC: EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3 Low Voltage Directive 2006/95/EC Safety: IEC 60950-1: 2005;EN 60950-1:2006 +A11:2009 FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Overscan: removes noise around the image. AV Mute: enables or disables AV Mute function. Closed Captions: enables or disables Closed Captions. Video: selects the audio input for video source. HDMI: select the audio input for HDMI signal. Keypad: enables or locks the projector keypad. LiteBoard™Wand: selects the LiteBoard™Wand mode. Options are: None, Single Pen and Dual Pens. See page 50 for details. Closed Captioning. . . Closed Captions: controls closed captioning. If the source is NTSC and contains captions on the selected channel, then the projector will display caption text overlaid on the image. When Closed Captions is off and volume is muted, closed captioning will appear. Options are: Off, CC1 and CC2. Image Setup. . . Digital Zoom: reduces the size of projector’s display area. If the display area has been resized by this setting, it can be moved by changing the Horz Shift and Vert Shift settings. Magnify Level: magnifies the image. If the image has been magnified by this setting, it can be moved by changing the Horz Shift and Vert Shift settings. Ceiling Mount: turns the image upside down for ceiling-mounted projection. Rear Project: reverses the image so you can project from behind a translucent screen. Blank Key: select what to display when the blank key on the remote is pressed: a solid color screen (blue, black or white), or the factory logo screen. Custom Key: allows you to assign a different function to the Custom button, allowing you to quickly and easily use the effect. Highlight an effect and press < or > to choose a different one. • • • • Blank Screen: displays a solid color or factory logo screen. Source: brings up a menu of available sources. Auto Image: resets the projector to the source. 28 Lamp. . . Programmed Dimming: When enabled, Programmed Dimming enhances contrast ratios, lamp life and system noise performance. Lamp power will change continuously based on the brightness of the program content. Note: Image anomalies may be seen when image scenes change from dark to light (or light to dark). Programmed Dimming works in conjunction with the lamp. If Lamp Low Power is enabled, Programmed Dimming is unavailable. Note: Programmed Dimming is off by default. To change the PIN: Select “Change PIN. . . ” in the Advanced Menu > Setup > PIN settings menu. Enter the new PIN. Power Power Saving Mode: When the Power Saving Mode is On and the projector is in standby (powered off but connected to AC power), external audio and the Monitor Out function will not work. [. . . ] Manage in accordance with local disposal laws. See www. lamprecycle. org. WARNINGS: • The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it may rupture with a popping sound if jolted, scratched, or handled while hot. The risk of lamp failure or rupture also increases as the lamp age increases; please replace the lamp when you see the “Replace Lamp” message. [. . . ]