User manual INFOCUS LITESHOW II

[. . . ] User's Guide 010-0643-01 *010-0643-00* Declaration of Conformity Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon 97070 USA European Office: Louis Armstrongweg 110, 1311 RL Almere, The Netherlands We declare under our sole responsibility that the LiteShow wireless adapter conforms to the following directives and norms: EMC Directive 89/336/EEC, Amended by 93/68/EEC EMC: EN 55022 EN 55024 ETSI EN 300 328 V1. 6. 1:2004 EN 301 489-01 V1. 5. 1:2004 EN 301 489-03 V1. 4. 1:2002 EN 301 489-17 V1. 2. 1:2002 EN 61000-3-2 EN 61000-3-3 Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC Safety: EN 60950: 2000 The Agency/Regulatory Approval for the computer's wireless adapter is solely the responsibility of the adapter manufacturer - not InFocus Corporation. Trademarks Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc. [. . . ] Select the Security type from among WEP 64 bit, WEP 128 bit, WPA-personal with TKIP encryption, and WPA2-Personal (PSK) then fill in the appropriate Key. NOTE: The security level increases as you move down the pulldown list. The security type selected here must match the security type of the existing Main network. IP Address By default, IP addresses are assigned automatically. If you want to specify one, click IP Address and provide the applicable information. 23 802. 1x This feature allows your LiteShow adapter to integrate into a secure wired corporate network. Contact your IT department if this feature is needed. If your network requires 802. 1x authentication, enter your information here. 24 Enterprise specific Advanced settings The Guest feature of Enterprise mode allows guests (people not registered on the main network) to project wirelessly to the LiteShow adapter without being granted access to the main network. 25 Guests By default, Allow guests is checked, meaning guests are allowed. To prevent guests from projecting, uncheck this box. Select what type of security applies to guests, if any. 26 Troubleshooting and Maintenance Reset the LiteShow II adapter Soft Reset A soft reset reboots the system with all user settings saved. Press the reset button for about one second. The LED turns off for two seconds, then the system reboots. Hard Reset A hard reset reboots the system with all factory default settings restored. Press the reset button for five seconds or more. The LED turns off for two seconds, then the system reboots. This will remove all password protection you may have applied previously. Category Power Issue LiteShow II has no power LiteShow II Power LED is not lit Connecting The LiteShow II device I want to connect to is not showing up in my LiteShow Manager "Connect to Projector" option is not available while using Windows XP Solution Verify the power supply connector is plugged into LiteShow II and a working AC power outlet. Verify that the projector and the LiteShow II device are both turned on, and that the LiteShow II splash screen is displaying. Verify the wireless network strength on the LiteShow Manager software. Adjust the antenna angle on the back of the adapter, if needed, to maximize the wireless network strength. Installation requires Administrator privileges. The "Connect to Projector" option will not work without Administrator privileges. Manually select the Wireless Network through the operating system after LiteShow Manager starts. Connecting 27 Category LED Issue LiteShow II Power LED is solid red Solution Wait one minute. Peer-to-Peer: If it still displays solid red after 2 minutes, perform a hard reset. [. . . ] InFocus or the service facility authorized by InFocus will return the repaired/replaced Product freight prepaid to the purchaser. Products returned for Warranty service must be accompanied by a written letter that: (i) explains the problem; (ii) provides proof of date of purchase; (iii) provides the dealer's name; and (iv) provides the model and serial number of the Product. Upon request of InFocus Corporation or an authorized repair center for InFocus, proof of legal import must accompany the warranty repair Product, otherwise the Product must be returned to the place of original purchase, to the manufacturer (Purchaser must bear all tax, duty and freight), or the Purchaser must bear charges for the warranty repair. No repair or replacement of Product or part thereof shall extend the Limited Warranty period as to the entire Product. [. . . ]