User manual INFOCUS LP570 Reference Guide

[. . . ] LCD PROJECTOR USER'S GUIDE fold and tear here fold and tear here Connecting the LitePro is summarized on the back of this card and described in detail in the LitePro 560/570 User's Guide. R The User's Guide contains instructions and illustrations for connections to all compatible computers. It also describes the remote control buttons and menu functions. 1 You must install the projection bulbs the first time you use the LitePro. 8 Refer to the "Read Me First" card or page 40 of the User's Guide for instructions. Connect the LitePro cable to the monitor connector on your computer. If you want to display your presentation on your computer 's monitor as well as on the projection screen, attach the "MONITOR" end of the LitePro cable to the end of the monitor's cable. 2 3 4 5 6 Place the LitePro on a flat surface within six feet of your power source and your computer. Make sure your computer and monitor are turned off. [. . . ] (Refer to "select/enter" on page 21 for additional information about the test pattern. ) To enable or disable the test pattern: 1. Press the menu button to display Menu 1. Use the right or left arrow buttons to highlight "Menu 2". Use the right or left arrow buttons to highlight "Test Pattern". Press select/enter to enable or disable the test pattern off. RS-232 When the LitePro's RS-232 connection is enabled, you can use the LitePro's remote control to send commands to your computer. To use this feature, you must install the Remote Control Programmer that was shipped with your LitePro. Refer to the Remote Control Programmer User's Guide for more information. To enable or disable the RS-232 serial port: 1. Press the menu button to display Menu 1. Use the right or left arrow buttons to highlight Menu 2. Use the right or left arrow buttons to highlight "RS-232". Press select/enter to enable or disable the RS-232 port. Auto Standby When you enable Auto Standby, the LitePro automatically turns off the projection lamp after a specified period of time. If Auto Standby is turned off, you can still turn off the lamp by pressing the standby button on the remote. Refer to page 17 and page 23 for additional information about Standby. LitePro 560/570 User's Guide 29 Using the LitePro To enable Auto Standby: 1. Press the menu button to display Menu 1. Use the right or left arrow buttons to highlight "Menu 2". Use the right or left arrow buttons to highlight "Auto Standby". Press select/enter to cycle through the settings. Reset The Reset function changes all the menu function settings back to the factory default states. The defaults are: · Rear Projection · Source Prompt · Auto Standby · Source Enable · Prog Button · Palette · Language · Video Type off on 30 minutes all sources enabled clear white 24, 389 English NTSC · Test Pattern · RS-232 · Reset · Text Mode · Comp(ress) · Sharpness · Loudness · Mute on on off off off off off off To reset your adjustments: 1. [. . . ] Refer to the In Focus Accessories Catalog for additional items. Item Read Me First card LitePro 560/570 User's Guide LiteShow II User's Guide Soft Carry Case Shipping Box ATA-Approved Hard Carry Case LitePro (VGA) Cable North American Power Cord Australian Power Cord UK Power Cord European Power Cord Danish Power Cord Swiss Power Cord Projection Lamps, 36V, 400W (set of 2) Lens Cover Mac Adapters (set of 2) Remote Control Programmer User's Guide Remote Control Programmer Software Remote Control Programmer (RS-232) Cable Remote Control Programmer (RS-232) Adapter RCA jack-to-mini plug adapter Remote Control LitePro Ceiling Mount Kit LiteShow Demo Disk LiteShow System Disk Fuse, 10A, 3AB (use w/110V) Fuse Holder for 10A, 3AB Fuse (use w/110V) Fuse, 6. 3A, 5x20mm (use w/220V) Fuse Holder for 6. 3A, 5x20mm Fuse (use w/220V) Part Number 009-0124-xx 010-0060-xx 010-0061-xx 110-0079-xx 110-0080-xx 591-0169-xx 210-0014-xx 210-0023-xx 210-0027-xx 210-0028-xx 210-0029-xx 210-0030-xx 210-0031-xx 232-0020-xx 340-0148-xx 516-0003-xx 010-0083-xx 599-0064-xx 210-0055-xx 515-0025-xx 515-0034-xx 590-0095-xx 591-0098-xx 599-0063-xx 599-0062-xx 749-0013-xx 749-0014-xx 749-0010-xx 749-0011-xx LitePro 560/570 User's Guide 53 Appendix Cable Connector Pin Assignments The Y-shaped LitePro cable that shipped with your LitePro has three connectors, they are labeled "Monitor", "Computer" and "LCD. " The pin assignments for these connectors are listed here. "LCD" Connector The end of the LitePro cable that plugs into the LitePro itself is a male 26-pin D-style connector. The table below lists its pin assignments. Input Pin 1 2 8 6 7 9 16 17 18 20 21 22 23 24 25 Signal Description Vertical sync Horizontal sync Blue analog reserved reserved Red analog reserved reserved Green analog GND GND GND Digital/analog video cable ID GND VGA/no video cable ID pin Output Pin 10 11 14 12 13 15 3 4 5 54 LitePro 560/570 User's Guide Appendix "Monitor" and "VGA" Connectors The pin assignments are the same for the "Monitor" and "VGA" connectors. The "Monitor" connector is a female video RGB, 15-pin micro-D-style connector. [. . . ]