User manual INFOCUS LP760 Reference Guide

[. . . ] fold and tear here fold and tear here Connecting the LitePro 760 is summarized on the back of this card and described in detail in the LitePro 760 User's Guide. R The User's Guide contains instructions and illustrations for IBMcompatible, Macintosh, PowerBook, X terminals and UNIX workstations. It also describes the remote control buttons and menu functions. 1 If you are setting up the LitePro projector for the first time, install the 2 bulbs that were shipped with the projector. Refer to the "Read Me First" card for instructions. Place the projector on a flat surface with the lens pointing towards the projection screen. [. . . ] standby When you press standby, the projector turns off its lamp to conserve electricity. The fans remain on to keep the LCD cool. When the projector cools sufficiently, the fans automatically turn down to a slower speed. Press any button on your remote to turn the lamp back on. arrow buttons The operation of the arrow buttons depends on whether or not the on-screen menu is displayed. When the menu is displayed, the left and right arrow buttons move the highlight bar to select a menu function. The up and down arrow buttons adjust the highlighted function. When the menu is not displayed, the arrow buttons move the image in the direction of the arrow. If your image is wider than 1024x768 pixels, use the arrow buttons to pan to the edges of the image. LitePro 760 User's Guide 19 Using the LitePro 760 The arrow buttons are auto-repeating; they repeat their function as long as you hold down the button. contrast Adjust the contrast if the white areas of the projected image do not appear to be solid white. To increase the contrast, press the contrast + button. To decrease the contrast, press the contrast - button. Both contrast buttons are auto-repeating; they continue to adjust the contrast setting as long as you hold down the button. You cannot adjust contrast in the LitePro test pattern. brightness Adjusting the brightness lightens or darkens the image. To lighten the image, press the + (plus) side of the brightness button. To darken the image, press the - (minus) side of the brightness button. Adjusting the brightness changes the amounts of red, green and blue in the image. If the LitePro menu is displayed when you press the brightness button, you will see the Red, Green and Blue values change accordingly. Both ends of the brightness button are auto-repeating; they continue to adjust the brightness setting as long as you hold down the button. sync Adjusting the synchronization fine tunes the LitePro to match the signals from your computer, decreasing fuzzy, streaked images. Press the sync + or sync - buttons to cycle through the sync levels until you find the one that best suits your computer. 20 LitePro 760 User's Guide Using the LitePro 760 Using the Menu The LitePro 760's on-screen menu allows you to adjust the individual colors in the projected image and change the following settings: · language of the menu · rear projection mode · color inversion · number of displayable colors · tracking · reset adjustments Each of the menu functions is described on the following pages in "Menu Functions". [. . . ] At 9, 000ft (2743m), the maximum temperature is 30°C. At 10, 000ft (3048m), the maximum temperature is 29°C. 42 LitePro 760 User's Guide Appendix Accessories Contact your In Focus dealer to order. Refer to the In Focus Accessories Catalog for additional items. Standard Accessories (ship with LitePro) Read Me First card LitePro 760 User's Guide Soft Carry Case Shipping Box LitePro Cable (VGA cable) Projection Lamp, 36V, 400W Mac Adapters (set of 2) BNC Adapters (2) 13W3 Adapters (2) Lens Cap Remote Control Part Number 009-0192-xx 010-0086-xx 110-0079-xx 110-0080-xx 210-0041-xx 232-0020-xx 516-0005-xx 515-0028-xx and 515-0029-xx 515-0030-xx and 515-0031-xx 340-0148-xx 590-0142-xx Power Cords (one ships with LitePro, depends on country) North American Power Cord Australian Power Cord UK Power Cord European Power Cord Danish Power Cord Swiss Power Cord Fuses and Fuse Holders (one set ships with LitePro, depends on country) Fuse, 10A, 3AB (use w/110V) Fuse Holder for 10A, 3AB Fuse (use w/110V) Fuse, 6. 3A, 5x20mm (use w/220V) Fuse Holder for 6. 3A, 5x20mm Fuse (use w/220V) Compatible Product LitePro Ceiling Mount Kit 591-0098-xx 749-0013-xx 749-0014-xx 749-0010-xx 749-0011-xx 210-0023-xx 210-0027-xx 210-0028-xx 210-0029-xx 210-0030-xx 210-0031-xx LitePro 760 User's Guide 43 Appendix Cable Connector Pin Assignments The Y-shaped LitePro cable that shipped with your LitePro has three connectors, they are labeled "Monitor", "Computer" and "LCD. " The pin assignments for these connectors are listed here. "LCD" Connector The end of the LitePro cable that plugs into the LitePro itself is a male 26-pin D-style connector. [. . . ]