User manual INFOCUS PROXIMA C445 Reference Guide

[. . . ] IN42/C445 NETWORKING GUIDE This guide is only intended to explain Network Functions. For safety, operations or any other issues, refer to the projector's User's Guide or Safety Booklet. TABLE OF CONTENTS Network Functions Before using the network functions Configuring and controlling the projector via a web browswer Settings Network Information Network Setting Mail Settings Alert Settings Schedule Settings Date/Time Settings Security Settings Projector Control Projector Status Network Restart Failure and Warning Alerts via E-mail Mail Settings Projector management via SNMP Controlling the projector via scheduling Date/Time Settings Schedule settings 2 2 3 5 6 7 8 9 10 11 12 13 14 15 15 15 17 18 18 18 1 Network Functions This projector is equipped with the following network functions. Configuring and Controlling the Projector via a Web Browser You can change the settings of or control the projector via a network by using a web browser from a PC that is connected to the same network. Failure & Warning Alerts via E-mail The projector can automatically send an alert to specified e-mail addresses when the projector requires maintenance or has encountered an error. Projector Management via SNMP This projector is SNMP (Simple Network Management Protocol) compliant, allowing you to monitor it from a remote location using SNMP software. Controlling the Projector via Scheduling You can schedule the projector to perform various functions according to the DATE and TIME. Before using the network functions To use the network functions of this projector, the projector must be configured to suit your network. Consult with your network administrator before connecting the projector to your network. Incorrect network configuration of this projector may cause problems on your network. [. . . ] The length of the recipient e-mail address can be up to 255 alphanumeric characters. Click the [Apply] button to save the settings. NOTE: · · You can confirm whether the mail settings work correctly using the [Send Test Mail] button. If you connect the projector to an existing network, consult a network administrator before setting server addresses. 8 Alert Settings Item Lamp won't strike Lamp Time Over Lamp unexpectedly goes out Fan failure Over temp condition Unidentifiable Error Lamp Cover Error Filter Time Over Temp Sensor Out Schedule Execution Error Overheating alarm Lamp time custom alarm Filter time custom alarm Description Lamp won't turn on after 5 attempts. Lamp has exceeded its specified lifetime. Lamp failed after it had successfully lit. The lamp door is not installed properly. Allows you to specify when (after how many hours) the lamp alarm message should be sent. Allows you to specify when (after how many hours) the filter alarm message should be sent. Clicking each Alert brings up a dialog box where you can specify that an email be sent to alert the appropriate personnel that an error has occurred. Subject can be 255 characters, Text can be 1024 characters. 9 Schedule Settings Item Daily Schedule Schedule List Sunday-Saturday Schedule Schedule List Specific date 1-5 Schedule Month/Day Schedule List Description Configures the daily schedule. Click the [Enable] check box to enable daily scheduling. Configures the Sunday through Saturday daily schedules. Click the [Enable] check box to enable daily scheduling. Configures the specific date (No. 1-5) schedule. Click the [Enable] check box to enable specific date (No. 1-5) scheduling. Displays the current specific date (No. 1-5) schedule. Click the [Apply] button to save the settings. To add additional functions and events click the [Add] button and set the following items. Item Time Command Power Parameter Source Parameter Description Configures the time to execute commands. Configures the parameters for power control. Configures the parameters for input switching. Click the [Register] button to add new commands to the Schedule List. Click the [Delete] button to delete commands from the Schedule list. 10 Date/Time Settings Item Current Date Current Time Daylight Savings Time Start-End Month/week/day/hour/minute Time difference SNTP SNTP Server IP Address Cycle Description Configures the current date in Year/Month/Day format. Configures the current time in Hour:Minute:Second format. Click the [ON] check box to enable daylight savings time and set the following items. Configures the date and time daylight savings time begins/ends. [. . . ] NOTE: · · · A Network Restart is required after the Community Name has been changed. Click [Network Restart] and configure the items. Make sure SNMP sysLocation and SNMP sysContact in the Network Settings page are defined. 17 Controlling the projector via scheduling The projector can be automatically controlled via scheduling. NOTE: · · · · You can schedule the following control events: Power ON/OFF, Input Source. [. . . ]