User manual INTELLINET 550710 SUPPLEMENTARY GUIDE

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual INTELLINET 550710. We hope that this INTELLINET 550710 user guide will be useful to you.

Lastmanuals help download the user guide INTELLINET 550710.

Download

Manual abstract: user guide INTELLINET 550710SUPPLEMENTARY GUIDE

Detailed instructions for use are in the User's Guide.

 [. . . ] INTELLINET ACTIVE NETWORKING 550710 ­ CGI Command Reference

February 17 2004 CGI Command Reference V 1. 3a for Network IP Camera This documentation explains the usage of CGI commands which are supported by Network IP Camera 550710. There are five different categories of CGI commands: 1) 2) 3) 4) 5) Still image request command Motion image request command GP_OUT Setting commands Setting Commands / Remote Programming Inquiry commands / Display of current settings & Alert State of Digital IO Connector

This reference is based on Firmware Version 4. 11 (Released: February 17 2004). You can get the latest firmware version here: http://www. intellinet-network. com/ipcamera

http://www. intellinet-network. com/ipcamera 1 of 13

INTELLINET ACTIVE NETWORKING 550710 ­ CGI Command Reference

1.  [. . . ] Value VGA QVGA QCIF Image Size 640 * 480 320 * 240 160 * 120

·

·

bf=<value> Controls the "behind firewall" parameter. Possible values are: 0 = behindfirewall = false (default value) 1 = behindfirewall = true If not specified the default value will be returned. timestamp=<value> Controls the "timestamp" parameter to display the date/time information in the live image. Possible values are: off = no timestamp on = timestamp = on (default value) If not specified the default value will be returned. 
http://www. intellinet-network. com/ipcamera 3 of 13

·

INTELLINET ACTIVE NETWORKING 550710 ­ CGI Command Reference 3. GP_OUT Setting commands These commands are to be used to control the GPIO (General Purpose I/O) output port of the camera. Syntax:
http://camera_ip/gp_out. cgi?id=<value>&passwd=<value>&out=<value>&interval=<value>

· · · ·

id=<value> Valid username (account must have administrator rights) passwd=<value> Valid password (account must have administrator rights) out=<value> Activates the Output port by using the value "on". interval=<value> Specifies the time in seconds the output port should be activated. Possible values are: 0 ­ 255

Example:
http://camera_ip/gp_out. cgi?id=guest&passwd=guest&out=on&interval=20

Camera activates the GPIO output for a period of 20 seconds. 

http://www. intellinet-network. com/ipcamera 4 of 13

INTELLINET ACTIVE NETWORKING 550710 ­ CGI Command Reference 4. Setting Commands / Remote Programming These commands are to be used to set various settings for the WEBVIEW. It is possible to transmit several parameters at one time only when they belong to the same CGI name (*_set. cgi). Syntax:
http://camera_ip/*_set. cgi?id=<value>&passwd=<value>&parameter=<value>

There are six different CGI Commands controlling different aspects: 1) Image setting command (image_set. cgi) Control Bightness,  Contrast,  Saturation and other image parameters. 2) Network setting command (network_set. cgi) Change the IP Address,  Ports,  SMTP Server,  . . . . 3) Event setting command (event_set. cgi) Setup the Event Trigger Configuration remotely. 4) Time setting command (time_set. cgi) Define the time server,  time zone,  daylight saving time,  . . . 5) System setting command (system_set. cgi) Configuration of Camera Name,  Location,  Direct Image Access and more 6) PTZ Control command (ptz_webctl. cgi) Command set for the PTZ Version of Network IP Camera. 

· ·

Always enter User ID and Password of an Administrator Account. parameter=<value> Refer to "CGI command list" below. 

http://www. intellinet-network. com/ipcamera 5 of 13

INTELLINET ACTIVE NETWORKING 550710 ­ CGI Command Reference 5.  [. . . ] Nuku'alofa

http://www. intellinet-network. com/ipcamera 12 of 13

INTELLINET ACTIVE NETWORKING 550710 ­ CGI Command Reference

PTZ Camera 550734

6. PTZ Control command (ptz_webctl. cgi)
http://camera_ip/ptz_webctl. cgi?id=<value>&passwd=<value>&cmd=<value>

cmd=<value>
Use one of the following values: up down left right zoom_in zoom_out focus_near focus_far stop In order to move the camera via te CGI commands,  you need to send two commands to the camera: Example: Move the camera up. 
http://camera_ip/ptz_webctl. cgi?id=<value>&passwd=<value>&cmd=up http://camera_ip/ptz_webctl. cgi?id=<value>&passwd=<value>&cmd=stop

Example: Move the camera left. 
http://camera_ip/ptz_webctl. cgi?id=<value>&passwd=<value>&cmd=left http://camera_ip/ptz_webctl. cgi?id=<value>&passwd=<value>&cmd=stop

Example: ZOOM the camera in
http://camera_ip/ptz_webctl. cgi?id=<value>&passwd=<value>&cmd=zoom_in http://camera_ip/ptz_webctl. cgi?id=<value>&passwd=<value>&cmd=stop Each DIRECTION command needs to be followed by a STOP command. If you do not send the STOP commend,  the camera keeps on moving until it reaches the physical limit of the PTZ unit (like all the way up,  all the way down). 

http://www. intellinet-network. com/ipcamera 13 of 13 [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE INTELLINET 550710

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual INTELLINET 550710 will begin.