User manual INTERMATIC HV402WLK2
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual INTERMATIC HV402WLK2. We hope that this INTERMATIC HV402WLK2 user guide will be useful to you.
Lastmanuals help download the user guide INTERMATIC HV402WLK2.
Manual abstract: user guide INTERMATIC HV402WLK2
Detailed instructions for use are in the User's Guide.
[. . . ] Remove existing light fixture from wall and any mounting hardware that may be present. Thread the 2 screws (A) into the mounting bracket provided with this wall light. (length of screws can be adjusted as needed). Attach mounting bracket to wall box with screws (C). [. . . ] Twist on wire connector · Connect black wire from light fixture to black wire from power source using a twist on wire connector. · Connect white wire from light fixture to white wire from power source using a twist on wire connector. · Attach the house grounding wire from the light fixture to the cross bar or wall box using the green grounding screw. Carefully tuck wires into wall box and cover plate.
Black Wire
White Wire
HV402WLKJ HV402WLKK
HV402WLKG HV402WLKH HV402WLKI
6 7 8 9 10
Attach light fixture to wall using 2 cap nuts taking care not to pinch wires between wall and light fixture. If installed screws are too long, or too short loosen locking nuts and adjust screw lengths as needed. IMPORTANT: Exceeding recommended maximum bulb wattage may cause over heating and risk of fire. Replace Top of light fixture by aligning slots on underside of top with locking tabs on light. Turn top in a clockwise direction approximately 1/2" to lock top. Restore power and test light for proper operation. IMPORTANT: After it has been determined the light is functioning properly, wall light must be sealed using a suitable RTV or silicone caulk around the top and sides of the cover plate to prevent water from entering the wall box. Leave the bottom un-caulked to allow moisture to escape.
IMPORTANT: For Missing/Damaged parts from newly purchased products go to: www. intermatic. com/warranty or call: 1-800-492-2289. For Replacement parts go to: www. intermatic. com/parts or call: 1-815-675-7000. Note: Matching low voltage and Solar light fixtures are available. See back of fixture carton.
AUTHORIZED SERVICE CENTER / CENTRO DE SERVICIO AUTORIZADO / CENTRE DE SERVICE ABRÉÉ Intermatic Incorporated After Sales Service 7777 Winn Road · Spring Grove, IL 60081-9698 158HV12409
www. intermatic. com
Instrucciones para armar e instalar las lámparas de pared Malibu®
Instructions pour assembler et installer les lampes murales Malibu®
ADVERTENCIA:
Para evitar el riesgo de shock eléctrico, verifique que la alimentación de energía esté apagada mientras instala o repara la lámpara.
AVERTISSEMENT :
Pour éviter tout risque de choc électrique, assurez-vous de couper le courant en installant ou réparant cette lampe.
NOTA: Antes de instalar, consulte el código eléctrico local para determinar los requisitos de cableado y conexión a tierra
REMARQUE : Avant d'installer, consultez vos codes d'électricité locaux pour connaître les exigences de câblage et de mise à la terre.
Herramientas recomendadas: Destornillador plano, Destornillador cruciforme, Pinzas (Podría necesitar herramientas adicionales para algunas instalaciones) Pasos sencillos:
PIEZA #
Outils recommandés : Tournevis enchoché, Tournevis Philips, Pinces (D'autres outils pourraient être nécessaires pour certaines installations) Étapes faciles à suivre :
HV402WLKA PIÈCE #
1 2 3
Desconecte la alimentación en el panel principal de interruptores de circuitos. Retire la lámpara existente de la pared y cualquier otro accesorio de instalación que pueda estar presente. Fije el soporte de montaje a la caja de pared. Atornille los 2 tornillos (A) en el soporte de montaje que viene con esta lámpara de pared. Asegure con dos tuercas de seguridad (B). (la longitud de los tornillos se puede ajustar como sea necesario). Fije el soporte de montaje a la caja de pared con los tornillos (C).
Modelo HV402WLK
1 2 3
Coupez le courant au panneau disjoncteur principal. Retirez la lampe actuelle du mur et toute autre quincaillerie qu'il pourrait y avoir. Installez la ferrure de montage à la boîte de jonction. [. . . ] Remettez le courant et essayez la lampe pour vérifier si elle fonctionne. IMPORTANT : Après avoir vérifié son fonctionnement, scellez la lampe murale à l'aide d'un produit de vulcanisation à la température de la pièce ou du mastic de silicone autour du dessus et des côtés de la plaque pour éviter que l'eau ne pénètre dans la boîte de jonction. N'intempérisez pas le dessous pour laisser échapper l'humidité.
IMPORTANTE: Si el producto que acaba de adquirir está incompleto o tiene piezas dañadas, notifique el problema a través de: www. intermatic. com/warranty o llame al: 1-800-492-2289. Para información sobre repuestos, visite: www. intermatic. com/parts o llame al: 1-815-675-7000. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE INTERMATIC HV402WLK2
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual INTERMATIC HV402WLK2 will begin.
