Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual IOGEAR GIC704SR5W6. We hope that this IOGEAR GIC704SR5W6 user guide will be useful to you.
Lastmanuals help download the user guide IOGEAR GIC704SR5W6.
Detailed instructions for use are in the User's Guide.
[. . . ] The reason this is necessary is because the used hard drive has system data on it which may cause recognition issues when configuring it for use with the RAID5 card. · RAID 0 and RAID1 setups require at least 2 drives, with RAID5 requiring 3 drives and RAID10 requiring 4 drives. If only one drive, make sure to have "Concatenate" or "Contiguous" setting.
4
Introduction
The board offers the ability to upgrade your desktop computer to RAID 5, RAID 0+1, RAID 0, or RAID 1 as well as JBOD. The board can control four independent Serial ATA channels. [. . . ] If using 2 Disks, do NOT select "Parity RAID" or "Mirrored Stripe" settings. If using 3 Disks, do NOT select the "Mirrored Stripe" setting. Open "Task Manager" to make sure the RAID setup is completed. RAID5 can take hours to complete, please be aware of these time requirements. Use Device Manager for hard disk initialization, partition and formatting within Windows.
12
BIOS (RAID Settings) Creating and deleting RAID sets is a function found in the BIOS. During boot up, the RAID setting message will appear and pause for a few moments to allow the user access to its settings. The board will act as a normal NON-RAID card when the BIOS does not have it configured for RAID. If you're using traditional parallel ATA HDDs, make sure your hard drives are set to master mode before accessing the RAID settings. As the BIOS boots, Press CTRL+S or F4 to enter the RAID bios utility. Press CTRL+E and then press Y to exit the setup. Continue with conventional Fdisk and Format steps to prepare the hard drives. Your RAID hardware configuration is complete. Proceed to software installation section. 13
Creating Mirrored Sets (RAID 1) 1. As the BIOS boots, Press CTRL+S or F4 to enter the RAID bios utility. Press CTRL+E and then press Y to exit the setup. Continue with conventional Fdisk and Format steps to prepare the hard drives. Your RAID hardware configuration is complete. Proceed to software installation section.
14
Creating a Mirrored-Striped Set (RAID 10) 1. As the BIOS boots, press CTRL+S or F4 to enter the RAID bios utility. Press Y and then press ESC to exit the setup. Continue with conventional Fdisk and Format steps to prepare the hard drives. [. . . ] IBM is a registered trademark of International Business Machines, Inc. Macintosh, G3/G4 and iMac are registered trademarks of Apple Computer, Inc. IOGEAR makes no warranty of any kind with regards to the information presented in this document. All information furnished here is for informational purposes only and is subject to change without notice. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE IOGEAR GIC704SR5W6
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual IOGEAR GIC704SR5W6 will begin.
