User manual IOGEAR GWAV8141K INSTALLATION

[. . . ] **Note: If you wish to use the PC Video Input Port for Component (YPbPr) media source, please use the included Component to VGA Adapter. 5 Receiver Unit Front View 1. PC Audio Output Port (3. 5mm Mini Stereo Jack)** 11. [. . . ] If none of the above works, please refer to the Factory Reset section to perform a factory reset on both transmitter unit and receiver unit. 2. If the connection has been established and you can see the IOGEAR screen; however, when you play a media from a source and it's not showing on your display: a. Please make sure the cables are properly connected. Please make sure you set the receiver unit to the correct output port. Check to your transmitter unit is switched to the correct port for your specific media source. Please make sure the display supports the resolution that the media source is streaming at. For example, if you are using a 720p HD display to play a full 1080p content, you would need to downscale the source's resolution to 720p to match the display. 11 Remote Control 1 POWER INFO TRANSMITTER 4 HDMI1 RECEIVER HDMI1 HDMI HDMI2 HDMI2 2 5 COMP PC PC AV VIDEO OUT AV VIDEO IN AV AUDIO IN 3 LAN WiFi CH 1 WiFi CH 2 6 1 POWER ON · · If the transmitter unit and receiver unit are powered off with the Power/Link LED on, press the power button will turn on both transmitter unit and receiver unit simultaneously If the transmitter unit and receiver unit are powered off with the Power/Link LED off, you need to press the power button to turn on the transmitter unit and receiver unit individually If the transmitter unit and receiver unit are powered on with the Power/Link LED on, press the power button will turn both transmitter unit and receiver unit off simultaneously with the Power/Link LED staying on If the transmitter unit and receiver unit are powered on with the Power/Link LED on, press and hold the power button for 6 seconds will turn both transmitter unit and receiver unit off simultaneously with the Power/Link LED off If the transmitter unit and receiver unit are powered on with the Power/Link LED flashing, you would need to power off the transmitter unit and receiver unit individually Press to select HDMI as the output Press to select Component as the output Press to select Composite as the output OFF · · · 2 Receiver unit HDMI Component AV 3 LAN Press and hold the LAN button for 6 seconds to change the connection to Wired Mode 12 4 INFO Press to display information* of the transmitter unit, receiver unit and display: Transmitter unit** · WiFi Channel · Firmware Version · Video/Audio Input Receiver unit · Connection · Firmware Version · Video Output · Display Resolution · WiFi Reception (1 to 5, 1 being weakest and 5 being strongest) Display Resolutions that the display can support *Note: The display information will disappear automatically after 20 seconds **Note: The transmitter unit's information will only be displayed if the connection between the transmitter unit and receiver unit has been established 5 Transmitter Unit HDMI1 Video HDMI1 Audio HDMI2 Video HDMI2 Audio AV Video AV Audio PC Video PC Audio HDMI1 Audio HDMI2 Audio Press to select HDMI1 as the video input Press to switch back to HDMI1 as the audio input Press to select HDMI2 as the video input Press to switch back to HDMI2 as the audio input Press to select Composite as the video input Press to select Composite as the audio input Press to select VGA/Component as the video input Press to select PC Audio-In as the audio input Press to switch back to the HDMI1 as the audio input Press to switch back to the HDMI2 as the audio input Note1: If you have switched to a specific video port via remote control without specifying the audio port on the transmitter unit, by default, it will also switch the audio to that specific port. Note2: Independent audio switching is only allowed for AV Audio and PC Audio. 6 WiFi CH 1 WiFi CH 2 Press and hold the specific WiFi Channel button for 6 seconds to change the connection to the specific WiFi Channel* *Note: If you change the WiFi channel while the wireless connection between the transmitter unit and receiver unit is established, both transmitter and receiver's WiFi channel will be changed simultaneously. If you change the WiFi channel while the wireless connection between the transmitter unit and receiver unit is not established, you would need to change and match up the same WiFi channel of the transmitter unit and receiver unit individually. 13 Selecting Specific Ports Front Panel Pushbutton You can cycle through the ports by pressing the front panel pushbutton Note: For the front panel pushbutton, both video and audio will switch port simultaneously. Remote Control You can press the specific port's button from the remote control Note 1: Video and audio will always switch simultaneously when switching receiver unit's output port. Note 2: If you have switched to a specific video port via remote control without specifying the audio port on the transmitter unit, by default, it will also switch the audio to that specific port. Note 3: Independent audio switching is only allowed for AV Audio and PC Audio. Note 4: You can select the transmitter unit's port by aiming the remote at the receiver unit or vice versa if and only if the connection between the transmitter unit and receiver unit has been established. [. . . ] only) or (949) 453-8782 Warranty Information This product carries a 1 Year Limited Warranty. For the terms and conditions of this warranty, please go to http://avior. iogear. com/support/warranty or call 1-866-946-4327 Contact Register online at http://avior. iogear. com/register Important Product Information Product Model Serial Number Contact IOGEAR 19641 Da Vinci Foothill Ranch, CA 92610 Toll Free: 866-9-IOGEAR Phone: 949-453-8782 Web site: avior. iogear. com E-mail: support@iogear. com 18 About Us FUN IOGEAR offers connectivity solutions that are innovative, fun, and stylish, helping people enjoy daily life using our high technology products. [. . . ]